Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userEffect of limiting the cathode surface on direct current microhollow cathode discharge in helium
270
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
This paper describes how to light several microdischarges in parallel without having to individually ballast each one. The V-I curve of a microhollow cathode discharge is characterized by a constant voltage in the normal glow regime because the plasma is able to spread over the cathode surface area to provide the additional secondary electrons needed. If one limits the cathode surface area, the V-I characteristic can be forced into an abnormal glow regime in which the operating voltage must increase with the current. It is then possible to light several microdischarges mounted in parallel without ballasting them individually.
rate research
Read More
Self-organized patterns of cathode spots in glow discharges are computed in the cathode boundary layer geometry, which is the one employed in most of the experiments reported in the literature. The model comprises conservation and transport equations of electrons and a single ion species, written in the drift-diffusion and local-field approximations, and Poissons equation. Multiple solutions existing for the same value of the discharge current and describing modes with different configurations of cathode spots are computed by means of a stationary solver. The computed solutions are compared to their counterparts for plane-parallel electrodes, and experiments. All of the computed spot patterns have been observed in the experiment.
The electron sheath formation in a DC magnetised plasma of modified hollow cathode source is studied. The discharge consists of two plane parallel cathodes and a small cubical anode placed off axis at the center. The argon plasma is produced and the properties of the plasma in response to the sheath formation near the anode are studied using electrical and optical diagnostics. In particular, the effect of pressure, magnetic field on discharge parameters such as discharge current, plasma potential, plasma density and electron temperature is studied. The discharge showed an onset of anode glow at a critical applied magnetic field indicating the formation of electron sheath and a double layer. The discharge current initially decreases; however it starts to rise again as the anode spot appears on the anode. The critical magnetic field at which anode glow formation takes place is dependent upon operating pressure and discharge voltage. The transition from ion sheath to electron sheath is investigated in detail by Langmuir probe and spectroscopy diagnostics. The plasma potential near the anode decreases during the transition from ion sheath to electron sheath. The plasma potential locks to the ionization potential of argon gas when anode spot is completely formed. A systematic study showed that during the transition, the electron temperature increases and plasma density decreases in the bulk plasma. The spectroscopy of the discharge showed presence of strong atomic and ionic lines of argon. The intensity of these spectral lines showed a dip during the transition between two sheaths. After the formation of the anode spot, oscillations of the order of 5-20 kHz are observed in the discharge current and floating potential due to the enhanced ionisation and excitation processes in the electron sheath.
The report is devoted to the results of the numerical study of the virtual cathode formation conditions in the relativistic electron beam under the influence of the self-magnetic and external axial magnetic fields. The azimuthal instability of the relativistic electron beam leading to the formation of the vortex electron structure in the system was found out. This instability is determined by the influence of the self-magnetic fields of the relativistic electron beam and it leads to the decrease of the critical value of the electron beam current (current when the non-stationary virtual cathode is formed in the drift space). The typical dependencies of the critical current on the external uniform magnetic field value were discovered. The effect of the beam thickness on the virtual cathode formation conditions was also analyzed.
To find a viable alternative to SF6 with growing climate change regulations, proper evaluation of alternatives such as compressed air ought to be done. For medium voltage applications, the withstand voltage is used as the dimensioning criteria and this is dependent on the initiation and propagation of streamers which are precursors to electrical breakdown. For design optimization, a thorough understanding of the initiation and propagation mechanisms of such electrical discharges under different stresses, pressure etc. ought to be studied experimentally and numerically also via a predictive model. Most of the numerical studies have so far been done via homemade codes as streamer models are not readily available in commercial software because of the complexity and non-linearity of such computations. Recently, with the increased robustness of the plasma module of the commercial finite element software, COMSOL(tm) Multiphysics, streamer discharge models can be developed with reasonable accuracy. In this paper, an implementation and validation approach is presented for streamer evolution in air for different voltage stresses. Results of simulations for short gaps ($le$ 5 mm) under Standard Temperature and Pressure (STP) conditions have been presented, analyzed and compared with some classical papers to evaluate the suitability of such a model for further studies of non-thermal electrical discharges. Index Terms-medium voltage, streamer discharges, eco-friendly gas, numerical models.
In order to study properties of short carbon arcs, a self-consistent model was implemented into a CFD code ANSYS-CFX. The model treats transport of heat and electric current in the plasma and the electrodes in a coupled manner and accounts for gas convection in the chamber. Multiple surface processes at the electrodes are modeled, including the formation of space-charge limited sheaths, ablation and deposition of carbon, emission and absorption of radiation and electrons. The simulations show that the arc is constricted near the cathode and the anode front surfaces leading to the formation of electrode spots. The cathode spot is a well-known phenomenon and mechanisms of its formation were reported elsewhere. However, the anode spot formation mechanism discovered in this work was not reported before. We conclude that the spot formation is not related to plasma instability, as commonly believed in case of constricted discharge columns, but rather occurs due to the highly nonlinear nature of heat balance in the anode. We additionally demonstrate this property with a reduced anode heat transfer model. We also show that the spot size increases with the arc current. This anode spot behavior was also confirmed in our experiments. Due to the anode spot formation, a large gradient of carbon gas density occurs near the anode, which drives a portion of the ablated carbon back to the anode at its periphery. This can consequently reduce the total ablation rate. Simulation results also show that the arc can reach local chemical equilibrium (LCE) state in the column region while the local thermal equilibrium (LTE) state is not typically achieved for experimental conditions. It shows that it is important to account for different electron and gas temperatures in the modeling of short carbon arcs.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
