Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userOptimizing magnetoresistive sensor signal-to-noise via pinning field tuning
69
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The presence of magnetic noise in magnetoresistive-based magnetic sensors degrades their detection limit at low frequencies. In this paper, different ways of stabilizing the magnetic sensing layer to suppress magnetic noise are investigated by applying a pinning field, either by an external field, internally in the stack or by shape anisotropy. We show that these three methods are equivalent, could be combined and that there is a competition between noise suppression and sensitivity reduction, which results in an optimum total pinning field, for which the detection limit of the sensor is improved up to a factor of ten.
rate research
Read More
We optimize the recording medium for heat-assisted magnetic recording by using a high/low $T_{mathrm{c}}$ bilayer structure to reduce AC and DC noise. Compared to a former work, small Gilbert damping $alpha=0.02$ is considered for the FePt like hard magnetic material. Atomistic simulations are performed for a cylindrical recording grain with diameter $d=5,$nm and height $h=8,$nm. Different soft magnetic material compositions are tested and the amount of hard and soft magnetic material is optimized. The results show that for a soft magnetic material with $alpha_{mathrm{SM}}=0.1$ and $J_{ij,mathrm{SM}}=7.72times 10^{-21},$J/link a composition with $50%$ hard and $50%$ soft magnetic material leads to the best results. Additionally, we analyse how much the areal density can be improved by using the optimized bilayer structure compared to the pure hard magnetic recording material. It turns out that the optimized bilayer design allows an areal density that is $1,$Tb/in$^2$ higher than that of the pure hard magnetic material while obtaining the same SNR.
In magnetic recording the signal-to-noise ratio (SNR) is a good indicator for the quality of written bits. However, a priori it is not clear which parameters have the strongest influence on the SNR. In this work, we investigate the role of the Gilbert damping on the SNR. Grains consisting of FePt like hard magnetic material with two different grain sizes $d_1=5,$nm and $d_2=7,$nm are considered and simulations of heat-assisted magnetic recording (HAMR) are performed with the atomistic simulation program VAMPIRE. The simulations display that the SNR saturates for damping constants larger or equal than 0.1. Additionally, we can show that the Gilbert damping together with the bit length have a major effect on the SNR whereas other write head and material parameters only have a minor relevance on the SNR.
We study causal waveform estimation (tracking) of time-varying signals in a paradigmatic atomic sensor, an alkali vapor monitored by Faraday rotation probing. We use Kalman filtering, which optimally tracks known linear Gaussian stochastic processes, to estimate stochastic input signals that we generate by optical pumping. Comparing the known input to the estimates, we confirm the accuracy of the atomic statistical model and the reliability of the Kalman filter, allowing recovery of waveform details far briefer than the sensors intrinsic time resolution. With proper filter choice, we obtain similar benefits when tracking partially-known and non-Gaussian signal processes, as are found in most practical sensing applications. The method evades the trade-off between sensitivity and time resolution in coherent sensing.
We demonstrate that photoemission properties of GaAs photocathodes (PCs) can be altered by surface acoustic waves (SAWs) generated on the PC surface due to dynamical piezoelectric fields of SAWs. Simulations with COMSOL indicate that electron effective lifetime in p-doped GaAs may increase by a factor of 10x to 20x. It implies a significant, by a factor of 2x to 3x, increase of quantum efficiency (QE) for GaAs PCs. Essential steps in device fabrication are demonstrated, including deposition of an additional layer of ZnO for piezoelectric effect enhancement, measurements of I-V characteristic of the SAW device, and ability to survive high-temperature annealing.
The hot disk transient plane source (TPS) method is a widely used standard technique (ISO 22007-2) for the characterization of thermal properties of materials, especially the thermal conductivity, k. Despite its well-established reliability for a wide variety of common materials, the hot disk TPS method is also known to suffer from a substantial systematic errors when applied to low-k thermal insulation materials. Here, we present a combined numerical and experimental study on the influence of the geometry of hot disk sensor on measured value of low-k materials. We demonstrate that the error is strongly affected by the finite thickness and thermal mass of the sensors insulation layer was well as the corresponding increase of the effective heater size beyond the radius of the embedded metal heater itself. We also numerically investigate the dependence of the error on the sample thermal properties, confirming that the errors are worse in low-k samples. A simple correction function is also provided, which converts the apparent (erroneous) result from a standard hot disk TPS measurement to a more accurate value. A standard polyimide sensor was also optimized using both wet and dry etching to provide more accurate measurement directly. Experimentally corrected value of k for Airloy x56 aerogel and a commercial silica aerogel using the numerical correction factor derived based on the standard TPS sensor is in excellent agreement with the directly measured value from the TPS sensor using the optimized polyimide sensor. Both of these methods can reduce the errors to less than 4% as compared to around 40% error of overestimation from raw values measured with the pristine sensor. Such results show that both the numerical correction to a pristine senor or an optimized sensor are capable of providing highly accurate value of thermal conductivity for such materials.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
