Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userThe superior role of the Gilbert damping on the signal-to-noise ratio in heat-assisted magnetic recording
109
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
In magnetic recording the signal-to-noise ratio (SNR) is a good indicator for the quality of written bits. However, a priori it is not clear which parameters have the strongest influence on the SNR. In this work, we investigate the role of the Gilbert damping on the SNR. Grains consisting of FePt like hard magnetic material with two different grain sizes $d_1=5,$nm and $d_2=7,$nm are considered and simulations of heat-assisted magnetic recording (HAMR) are performed with the atomistic simulation program VAMPIRE. The simulations display that the SNR saturates for damping constants larger or equal than 0.1. Additionally, we can show that the Gilbert damping together with the bit length have a major effect on the SNR whereas other write head and material parameters only have a minor relevance on the SNR.
rate research
Read More
We optimize the recording medium for heat-assisted magnetic recording by using a high/low $T_{mathrm{c}}$ bilayer structure to reduce AC and DC noise. Compared to a former work, small Gilbert damping $alpha=0.02$ is considered for the FePt like hard magnetic material. Atomistic simulations are performed for a cylindrical recording grain with diameter $d=5,$nm and height $h=8,$nm. Different soft magnetic material compositions are tested and the amount of hard and soft magnetic material is optimized. The results show that for a soft magnetic material with $alpha_{mathrm{SM}}=0.1$ and $J_{ij,mathrm{SM}}=7.72times 10^{-21},$J/link a composition with $50%$ hard and $50%$ soft magnetic material leads to the best results. Additionally, we analyse how much the areal density can be improved by using the optimized bilayer structure compared to the pure hard magnetic recording material. It turns out that the optimized bilayer design allows an areal density that is $1,$Tb/in$^2$ higher than that of the pure hard magnetic material while obtaining the same SNR.
The signal-to-noise ratio (SNR) of a bit series written with heat-assisted magnetic recording (HAMR) on granular media depends on a large number of different parameters. The choice of material properties is essential for the obtained switching probabilities of single grains and therefore for the written bits quality in terms of SNR. Studies where the effects of different material compositions on transition jitter and the switching probability are evaluated were done, but it is not obvious, how significant those improvements will finally change the received SNR. To investigate that influence, we developed an analytical model of the switching probability phase diagram, which contains independent parameters for, inter alia, transition width, switching probability and curvature. Different values lead to corresponding bit patterns on granular media, where a reader model detects the resulting signal, which is finally converted to a parameter dependent SNR value. For grain diameters between 4 and 8nm, we show an increase of ~10dB for bit lengths between 4 and 12nm, an increase of ~9dB for maximum switching probabilities between 0.64 and 1.00, a decrease of ~5dB for down-track-jitter parameters between 0 and 4nm and an increase of ~1dB for reduced bit curvature. Those results are furthermore compared to the theoretical formulas for the SNR. We obtain a good agreement, even though we show slight deviations.
Enhancing light absorption in the recording media layer can improve the energy efficiency and prolong the device lifetime in heat assisted magnetic recording (HAMR). In this work, we report the design and implementation of a resonant nanocavity structure to enhance the light-matter interaction within an ultrathin FePt layer. In a Ag/SiO2/FePt trilayer structure, the thickness of the dielectric SiO2 layer is systematically tuned to reach maximum light absorption at the wavelength of 830 nm. In the optimized structure, the light reflection is reduced by more than 50%. This results in effective laser heating of the FePt layer, as imaged by an infrared camera. The scheme is highly scalable for thinner FePt layers and shorter wavelengths to be used in future HAMR technologies.
The reduction of the transition curvature of written bits in heat-assisted magnetic recording (HAMR) is expected to play an important role for the future areal density increase of hard disk drives. Recently a write head design with flipped write and return poles was proposed. In this design a large spatial field gradient of the write head was the key to significantly reduce the transition curvature. In this work we optimized the write pole of a heat-assisted magnetic recording head in order to produce large field gradients as well as large fields in the region of the heat pulse. This is done by topology optimization. The simulations are performed with dolfin-adjoint. For the maximum field gradients of $8.1,$mT/nm, $8.6,$mT/nm and $11.8,$mT/nm, locally resolved footprints of an FePt like hard magnetic recording medium are computed with a coarse-grained Landau-Lifshitz-Bloch (LLB) model and the resulting transition curvature is analysed. Additional simulations with a bilayer structure with $50%$ hard and $50%$ soft magnetic material are computed. The results show that for both recording media, the optimized head design does not lead to any significant improvement of the written track. Thus, we analyse the transition curvature for the optimized write heads theoretically with an effective recording time window (ERTW) model. Moreover, we check how higher field gradients influence the curvature reduction. The results show that a simple optimization of the conventional head design design is not sufficient for effective curvature reduction. Instead, new head concepts will be needed to reduce transition curvature.
In this paper we apply an extended Landau-Lifschitz equation, as introduced by Bav{n}as et al. for the simulation of heat-assisted magnetic recording. This equation has similarities with the Landau-Lifshitz-Bloch equation. The Bav{n}as equation is supposed to be used in a continuum setting with sub-grain discretization by the finite-element method. Thus, local geometric features and nonuniform magnetic states during switching are taken into account. We implement the Bav{n}as model and test its capability for predicting the recording performance in a realistic recording scenario. By performing recording simulations on 100 media slabs with randomized granular structure and consecutive read back calculation, the write position shift and transition jitter for bit lengths of 10nm, 12nm, and 20nm are calculated.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
