Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMaximum efficiencies and performance limiting factors of inorganic and hybrid perovskite solar cells
57
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The Shockley and Queisser limit, a well-known efficiency limit for a solar cell, is based on unrealistic physical assumptions and its maximum limit is seriously overestimated. To understand the power loss mechanisms of record-efficiency cells, a more rigorous approach is necessary. Here, we have established a new formalism that can accurately predict absolute performance limits of solar cells in conventional thin film form. In particular, we have estimated the maximum efficiencies of 13 well-studied solar cell materials [GaAs, InP, CdTe, a-Si:H, CuInSe2, CuGaSe2, CuInGaSe2, Cu2ZnSnSe4, Cu2ZnSnS4, Cu2ZnSn(S,Se)4, Cu2ZnGeSe4, CH3NH3PbI3, HC(NH2)2PbI3] in a 1-um-thick physical limit. Our calculation shows that over 30% efficiencies can be achieved for absorber layers with sharp absorption edges (GaAs, InP, CdTe, CuInGaSe2, Cu2ZnGeSe4). Nevertheless, many record-efficiency polycrystalline solar cells, including hybrid perovskites, are limited by open-circuit voltage and fill-factor losses. We show that the maximum conversion efficiencies described here present new alternative limits that can predict the power generation of real-world solar cells.
rate research
Read More
The performance of organometallic perovskite solar cells has rapidly surpassed that of both conventional dye-sensitised and organic photovoltaics. High power conversion efficiency can be realised in both mesoporous and thin-film device architectures. We address the origin of this success in the context of the materials chemistry and physics of the bulk perovskite as described by electronic structure calculations. In addition to the basic optoelectronic properties essential for an efficient photovoltaic device (spectrally suitable band gap, high optical absorption, low carrier effective masses), the materials are structurally and compositionally flexible. As we show, hybrid perovskites exhibit spontaneous electric polarisation; we also suggest ways in which this can be tuned through judicious choice of the organic cation. The presence of ferroelectric domains will result in internal junctions that may aid separation of photoexcited electron and hole pairs, and reduction of recombination through segregation of charge carriers. The combination of high dielectric constant and low effective mass promotes both Wannier-Mott exciton separation and effective ionisation of donor and acceptor defects. The photoferroic effect could be exploited in nanostructured films to generate a higher open circuit voltage and may contribute to the current-voltage hysteresis observed in perovskite solar cells.
We explore the degradation behaviour under continuous illumination and direct oxygen exposure of inverted unencapsulated formamidinium(FA)0.83Cs0.17Pb(I0.8Br0.2)3, CH3NH3PbI3, and CH3NH3PbI3-xClx perovskite solar cells. We continuously test the devices in-situ and in-operando with current-voltage sweeps, transient photocurrent, and transient photovoltage measurements, and find that degradation in the CH3NH3PbI3-xClx solar cells due to oxygen exposure occurs over shorter timescales than FA0.83Cs0.17Pb(I0.8Br0.2)3 mixed-cation devices. We attribute these oxygen-induced losses in the power conversion efficiencies to the formation of electron traps within the perovskite photoactive layer. Our results highlight that the formamidinium-caesium mixed-cation perovskites are much less sensitive to oxygen-induced degradation than the methylammonium-based perovskite cells, and that further improvements in perovskite solar cell stability should focus on the mitigation of trap generation during ageing.
In this study, the optoelectronic properties of a monolithically integrated series-connected tandem solar cell are simulated. Following the large success of hybrid organic-inorganic perovskites, which have recently demonstrated large efficiencies with low production costs, we examine the possibility of using the same perovskites as absorbers in a tandem solar cell. The cell consists in a methylammonium mixed bromide-iodide lead perovskite, CH3NH3PbI3(1-x)Br3x (0 < x < 1), top sub-cell and a single-crystalline silicon bottom sub-cell. A Si-based tunnel junction connects the two sub-cells. Numerical simulations are based on a one-dimensional numerical drift-diffusion model. It is shown that a top cell absorbing material with 20% of bromide and a thickness in the 300-400 nm range affords current matching with the silicon bottom cell. Good interconnection between single cells is ensured by standard n and p doping of the silicon at 5.10^19cm-3 in the tunnel junction. A maximum efficiency of 27% is predicted for the tandem cell, exceeding the efficiencies of stand-alone silicon (17.3%) and perovskite cells (17.9%) taken for our simulations, and more importantly, that of the record crystalline Si cells.
In this perspective, we explore the insights into the device physics of perovskite solar cells gained from modeling and simulation of these devices. We discuss a range of factors that influence the modeling of perovskite solar cells, including the role of ions, dielectric constant, density of states, and spatial distribution of recombination losses. By focusing on the effect of non-ideal energetic alignment in perovskite photovoltaic devices, we demonstrate a unique feature in low recombination perovskite materials - the formation of an interfacial, primarily electronic, self-induced dipole that results in a significant increase in the built-in potential and device open-circuit voltage. Finally, we discuss the future directions of device modeling in the field of perovskite photovoltaics, describing some of the outstanding open questions in which device simulations can serve as a particularly powerful tool for future advancements in the field.
The scalability of highly efficient organic-inorganic perovskite solar cells (PSCs) is one of the remaining challenges of solar module manufacturing. Various scalable methods have been explored to strive for uniform perovskite films of high crystal quality on large-area substrates. However, each of these methods have individual drawbacks, limiting the successful commercialization of perovskite photovoltaics. Here, we report a fully scalable hybrid process, which combines vapor- and solution-based techniques to deposit high quality uniform perovskite films on large-area substrates. This two-step process does not use toxic solvents, and it further allows facile implementation of passivation strategies and additives. We fabricated PSCs based on this process and used blade coating to deposit both charge transporting layers (SnO2 and Spiro-OMeTAD) without hazardous solvents in ambient air. The fabricated PSCs have yielded open-circuit voltage up to 1.16 V and power conversion efficiency of 18.7 % with good uniformity on 5 cm x 5 cm substrates.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
