Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userCEP-stable high-energy ytterbium doped fiber amplifier
80
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We report on the CEP stabilization of an Yb-doped fiber amplifier system delivering 30 microjoules, 100 fs pulses at 100 kHz repetition rate. A single shot, every shot, measurement of the CEP stability based on a simple f-2f interferometer is performed, yielding a CEP standard deviation of 320 mrad rms over 1 s. Long-term stability is also assessed, with 380 mrad measured over one hour. This level of performance is allowed by a hybrid architecture including a passively CEP-stabilized front-end based on difference frequency generation, and an active CEP stabilization loop for the fiber amplifier system, acting on a telecom-grade integrated LiNbO3 phase modulator. These results demonstrate the full compatibility of Yb-doped high repetition rate laser for attoscience.
rate research
Read More
Generally speaking, the self-sweeping effect relies on the dynamical grating formed in a gain fiber. Here, the normal self-sweeping was generated in a pump-free ytterbium-doped fiber which serves as a fiber saturable absorber and is introduced to the laser cavity by a circulator in this experiment. The sweeping rate and the sweeping range alter as usual, both of which can be controlled by the pump power. Further, a new self-pulse signal is observed and discussed in this work, which shows the difference of the self-sweeping effects between active fiber and fiber saturable absorber.
Diamond containing the negatively charged nitrogen-vacancy (NV) center is emerging as a significant new system for magnetometry. However, most NV sensors require microscopes to collect the fluorescence signals and are therefore limited to laboratory settings. By incorporating micron-scale diamond particles at an annular interface within the cross section of a silicate glass fiber, a high-sensitivity and robust fiber platform for magnetic field sensing is demonstrated here. The fluorescence and spin properties of NV centers embedded in the diamond crystals are well preserved during the fiber drawing process, leading to enhanced continuous-wave diamond-magnetometry in fiber-transmitted sensing configurations. The interface doping of diamond particles also leads to reduced fiber propagation loss and benefits the guidance of NV-fluorescence in the hybrid fiber. Using the diamond-fiber system, magnetic field readout through 50 cm of fiber is achieved. This study paves the way for novel fiber-based diamond sensors for field-deployable quantum metrology applications.
We report on the design and whole characterization of low-noise and affordable-cost Yb-doped double-clad fiber amplifiers operating at room temperature in the near-infrared spectral region at pulse repetition rate of 160 MHz. Two different experimental configurations are discussed. In the first one, a broadband seed radiation with a transform limited pulse duration of 71 fs, an optical spectrum of 20 nm wide at around 1040 nm, and 20 mW average power is adopted. In the second configuration, the seed radiation is constituted by stretched pulses with a time duration as long as 170 ps, with a 5-nm narrow pulse spectrum centered at 1029 nm and 2 mW average input power. In both cases we obtained transform limited pulse trains with an amplified output power exceeding 2 W. Furthermore, relative intensity noise measurements show that no significant noise degradation occurs during the amplification process.
The interplay of such cornerstones of modern nonlinear fiber optics as a nonlinearity, stochasticity and polarization leads to variety of the noise induced instabilities including polarization attraction and escape phenomena harnessing of which is a key to unlocking the fiber optic systems specifications required in high resolution spectroscopy, metrology, biomedicine and telecommunications. Here, by using direct stochastic modeling, the mapping of interplay of the Raman scattering-based nonlinearity, the random birefringence of a fiber, and the pump-to-signal intensity noise transfer has been done in terms of the fiber Raman amplifier parameters, namely polarization mode dispersion, the relative intensity noise of the pump laser, fiber length, and the signal power. The obtained results reveal conditions for emergence of the random birefringence-induced resonance-like enhancement of the gain fluctuations (stochastic anti-resonance) accompanied by pulse broadening and rare events in the form of low power output signals having probability heavily deviated from the Gaussian distribution.
High-dimensional quantum states have already settled their advantages in different quantum technology applications. However, their reliable transmission in fiber links remains an open challenge that must be addressed to boost their application, e.g. in the future quantum internet. Here, we prove how path encoded high-dimensional quantum states can be reliably transmitted over a 2 km long multicore fiber, taking advantage of a phase-locked loop system guaranteeing a stable interferometric detection.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
