Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userRelaxed micromorphic model of transient wave propagation in anisotropic band-gap metastructures
49
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
In this paper, we show that the transient waveforms arising from several localised pulses in a micro-structured material can be reproduced by a corresponding generalised continuum of the relaxed micromorphic type. Specifically, we compare the dynamic response of a bounded micro-structured material to that of bounded continua with special kinematic properties: (i) the relaxed micromorphic continuum and (ii) an equivalent Cauchy linear elastic continuum. We show that, while the Cauchy theory is able to describe the overall behaviour of the metastructure only at low frequencies, the relaxed micromorphic model goes far beyond by giving a correct description of the pulse propagation in the frequency band-gap and at frequencies intersecting the optical branches. In addition, we observe a computational time reduction associated with the use of the relaxed micromorphic continuum, compared to the sensible computational time needed to perform a transient computation in a micro-structured domain.
rate research
Read More
We rigorously determine the scale-independent short range elastic parameters in the relaxed micromorphic generalized continuum model for a given periodic microstructure. This is done using both classical periodic homogenization and a new procedure involving the concept of apparent material stiffness of a unit-cell under affine Dirichlet boundary conditions and Neumanns principle on the overall representation of anisotropy. We explain our idea of maximal stiffness of the unit-cell and use state of the art first order numerical homogenization methods to obtain the needed parameters for a given tetragonal unit-cell. These results are used in the accompanying paper [16] to describe the wave propagation including band-gaps in the same tetragonal metamaterial.
The information carrier of modern technologies is the electron charge whose transport inevitably generates Joule heating. Spin-waves, the collective precessional motion of electron spins, do not involve moving charges and thus avoid Joule heating. In this respect, magnonic devices in which the information is carried by spin-waves attract interest for low-power computing. However implementation of magnonic devices for practical use suffers from low spin-wave signal and on/off ratio. Here we demonstrate that cubic anisotropic materials can enhance spin-wave signals by improving spin-wave amplitude as well as group velocity and attenuation length. Furthermore, cubic anisotropic material shows an enhanced on/off ratio through a laterally localized edge mode, which closely mimics the gate-controlled conducting channel in traditional field-effect transistors. These attractive features of cubic anisotropic materials will invigorate magnonics research towards wave-based functional devices.
Hysteretic damping is often modeled by means of linear viscoelastic approaches such as nearly constant Attenuation (NCQ) models. These models do not take into account nonlinear effects either on the stiffness or on the damping, which are well known features of soil dynamic behavior. The aim of this paper is to propose a mechanical model involving nonlinear viscoelastic behavior for isotropic materials. This model simultaneously takes into account nonlinear elasticity and nonlinear damping. On the one hand, the shear modulus is a function of the excitation level; on the other, the description of viscosity is based on a generalized Maxwell body involving non-linearity. This formulation is implemented into a 1D finite element approach for a dry soil. The validation of the model shows its ability to retrieve low amplitude ground motion response. For larger excitation levels, the analysis of seismic wave propagation in a nonlinear soil layer over an elastic bedrock leads to results which are physically satisfactory (lower amplitudes, larger time delays, higher frequency content).
In this paper propagation properties of a parallel-plate waveguide with tunable artificial impedance surfaces as sidewalls are studied both analytically and numerically. The impedance surfaces comprise an array of patches over a dielectric slab with embedded metallic vias. The tunability of surfaces is achieved with varactors. Simple design equations for tunable artificial impedance surfaces as well as dispersion equations for the TE and TM modes are presented. The propagation properties are studied in three different regimes: a multi-mode waveguide, a single-mode waveguide, and below-cutoff waveguide. The analytical results are verified with numerical simulations.
It is demonstrated in this paper that the propagation of the electric wave field in a heterogeneous medium in 3D can sometimes be governed well by a single PDE, which is derived from the Maxwells equations. The corresponding component of the electric field dominates two other components. This justifies some past results of the second author with coauthors about numerical solutions of coefficient inverse problems with experimental electromagnetic data. In addition, since it is simpler to work in applications with a single PDE rather than with the complete Maxwells system, then the result of this paper might be useful to researchers working on applied issues of the propagation of electromagnetic waves in inhomogeneous media.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
