Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userDesign of an on-chip superconducting microwave circulator with octave bandwidth
320
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We present a design for a superconducting, on-chip circulator composed of dynamically modulated transfer switches and delays. Design goals are set for the multiplexed readout of superconducting qubits. Simulations of the device show that it allows for low-loss circulation (insertion loss < 0.35 dB and isolation >20 dB) over an instantaneous bandwidth of 2.3 GHz. As the device is estimated to be linear for input powers up to -65 dBm, this design improves on the bandwidth and power-handling of previous superconducting circulators by over a factor of 50, making it ideal for integration with broadband quantum limited amplifiers.
rate research
Read More
We analyze the design of a potential replacement technology for the commercial ferrite circulators that are ubiquitous in contemporary quantum superconducting microwave experiments. The lossless, lumped element design is capable of being integrated on chip with other superconducting microwave devices, thus circumventing the many performance-limiting aspects of ferrite circulators. The design is based on the dynamic modulation of DC superconducting microwave quantum interference devices (SQUIDs) that function as nearly linear, tunable inductors. The connection to familiar ferrite-based circulators is a simple frame boost in the internal dynamics equation of motion. In addition to the general, schematic analysis, we also give an overview of many considerations necessary to achieve a practical design with a tunable center frequency in the 4-8 GHz frequency band, a bandwidth of 240 MHz, reflections at the -20 dB level, and a maximum signal power of approximately order 100 microwave photons per inverse bandwidth.
We report on the design and performance of an on-chip microwave circulator with a widely (GHz) tunable operation frequency. Non-reciprocity is created with a combination of frequency conversion and delay, and requires neither permanent magnets nor microwave bias tones, allowing on-chip integration with other superconducting circuits without the need for high-bandwidth control lines. Isolation in the device exceeds 20 dB over a bandwidth of tens of MHz, and its insertion loss is small, reaching as low as 0.9 dB at select operation frequencies. Furthermore, the device is linear with respect to input power for signal powers up to hundreds of fW ($approx 10^3$ circulating photons), and the direction of circulation can be dynamically reconfigured. We demonstrate its operation at a selection of frequencies between 4 and 6 GHz.
Microwave circulators play an important role in quantum technology based on superconducting circuits. The conventional circulator design, which employs ferrite materials, is bulky and involves strong magnetic fields, rendering it unsuitable for integration on superconducting chips. One promising design for an on-chip superconducting circulator is based on a passive Josephson-junction ring. In this paper, we consider two operational issues for such a device: circuit tuning and the effects of quasiparticle tunneling. We compute the scattering matrix using adiabatic elimination and derive the parameter constraints to achieve optimal circulation. We then numerically optimize the circulator performance over the full set of external control parameters, including gate voltages and flux bias, to demonstrate that this multi-dimensional optimization converges quickly to find optimal working points. We also consider the possibility of quasiparticle tunneling in the circulator ring and how it affects signal circulation. Our results form the basis for practical operation of a passive on-chip superconducting circulator made from a ring of Josephson junctions.
We describe a scheme to coherently convert a microwave photon of a superconducting co-planar waveguide resonator to an optical photon emitted into a well-defined temporal and spatial mode. The conversion is realized by a cold atomic ensemble trapped above the surface of the superconducting atom chip, near the antinode of the microwave cavity. The microwave photon couples to a strong Rydberg transition of the atoms that are also driven by a pair of laser fields with appropriate frequencies and wavevectors for an efficient wave-mixing process. With only few thousand atoms in an ensemble of moderate density, the microwave photon can be completely converted into an optical photon emitted with high probability into the phase matched direction and, e.g., fed into a fiber waveguide. This scheme operates in a free-space configuration, without requiring strong coupling of the atoms to a resonant optical cavity.
As the field of quantum computing progresses to larger-scale devices, multiplexing will be crucial to scale quantum processors. While multiplexed readout is common practice for superconducting devices, relatively little work has been reported about the combination of flux and microwave control lines. Here, we present a method to integrate a microwave line and a flux line into a single XYZ line. This combined control line allows us to perform fast single-qubit gates as well as to deliver flux signals to the qubits. The measured relaxation times of the qubits are comparable to state-of-art devices employing separate control lines. We benchmark the fidelity of single-qubit gates with randomized benchmarking, achieving a fidelity above 99.5%, and we demonstrate that XYZ lines can in principle be used to run parametric entangling gates.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
