Do you want to publish a course? Click here

Beyond 100 nm Resolution in 3D Laser Lithography: Post Processing Solutions

71   0   0.0 ( 0 )
 Publication date 2018
  fields Physics
and research's language is English




Ask ChatGPT about the research

Laser polymerization has emerged as a direct writing technique allowing the fabrication of complex 3D structures with microscale resolution. The technique provides rapid prototyping capabilities for a broad range of applications, but to meet the growing interest in 3D nanoscale structures the resolution limits need to be pushed beyond the 100 nm benchmark, which is challenging in practical implementations. As a possible path towards this goal, a post processing of laser polymerized structures is presented. Precise control of the cross-sectional dimensions of structural elements as well as tuning of an overall size of the entire 3D structure was achieved by combining isotropic plasma etching and pyrolysis. The smallest obtainable feature sizes are mostly limited by the mechanical properties of the polymerized resist and the geometry of 3D structure. Thus the demonstrated post processing steps open new avenues to explore free form 3D structures at the nanoscale.



rate research

Read More

To take fully advantage of Junctionless transistor (JLT) low-cost and low-temperature features we investigate a 475 degC process to create onto a wafer a thin poly-Si layer on insulator. We fabricated a 13nm doped (Phosphorous, 1E19 at/cm3) poly-silicon film featuring excellent roughness values (Rmax= 1.6nm and RMS=0.2nm). Guidelines for grain size optimization using nanosecond (ns) laser annealing are given.
Plasmonic color printing with semicontinuous metal films is a lithography-free, non-fading, and environment-friendly method of generation of bright colors. Such films are comprised of metal nanoparticles, which resonate at different wavelengths upon light illumination depending on the size and shape of the nanoparticles. To achieve an experimentally demonstrated structure that was optimized in terms of broader color range and increased stability, variable Ag semicontinuous metal films were deposited on a metallic mirror with a sub-wavelength-thick dielectric spacer. Femtosecond laser post-processing was then introduced to extend the color gamut through spectrally induced changes from blue to green, red, and yellow. Long-term stability and durability of the structures were addressed to enable non-fading colors with an optimized overcoating dielectric layer. The thickness of the proposed designs is on the order of 100 nanometers, and it can be deposited on any substrate. These structures generate a broad range of long-lasting colors in reflection that can be applied to real-life artistic or technological applications with a spatial resolution on the order of 0.3 mm or less.
In spite of the fact that there are different techniques in the creation of the high-quality liquid crystals (LCs) alignment by means of various surfaces, the azimuthal and polar anchoring energies as well as the pre-tilt angle are important parameters to all of them. Here, the modified by a certain manner aligning layers, previously formed by nonlinear laser lithography (NLL), having high-quality nano-periodic grooves on Ti surfaces, recently proposed for LC alignment was studied. The change of the scanning speed of NLL in the process of nano-structured Ti surfaces and their further modification by means of ITO-coating, and deposition of polyimide film has enabled different aligning layers, whose main characteristics, namely azimuthal and polar anchoring energies, were measured. For the modified aligning layers, the dependencies of the twist and pre-tilt angles for LC cells filled by nematic E7 ({Delta}{epsilon} > 0) and MLC-6609 ({Delta}{epsilon} < 0) were obtained. Also the contact angle for droplets of isotropic liquid (glycerol), and nematic LCs was measured for the various values of the scanning speed during the laser processing.
Multi-scale computational approaches are important for studies of novel, low-dimensional electronic devices since they are able to capture the different length-scales involved in the device operation, and at the same time describe critical parts such as surfaces, defects, interfaces, gates, and applied bias, on a atomistic, quantum-chemical level. Here we present a multi-scale method which enables calculations of electronic currents in two-dimensional devices larger than 100 nm$^2$, where multiple perturbed regions described by density functional theory (DFT) are embedded into an extended unperturbed region described by a DFT-parametrized tight-binding model. We explain the details of the method, provide examples, and point out the main challenges regarding its practical implementation. Finally we apply it to study current propagation in pristine, defected and nanoporous graphene devices, injected by chemically accurate contacts simulating scanning tunneling microscopy probes.
Carbon Nanotubes (CNTs)-polymer composites are promising candidates for a myriad of applications. Ad-hoc CNTs-polymer composite fabrication techniques inherently pose roadblock to optimized processing resulting in microstructural defects i.e., void formation, poor interfacial adhesion, wettability, and agglomeration of CNTs inside the polymer matrix. Although improvement in the microstructures can be achieved via additional processing steps such as-mechanical methods and/or chemical functionalization, the resulting composites are somewhat limited in structural and functional performances. Here, we demonstrate that 3D printing technique like-direct ink writing offers improved processing of CNTs-polymer composites. The shear-induced flow of an engineered nanocomposite ink through the micronozzle offers some benefits including reducing the number of voids within the epoxy, improving CNTs dispersion and adhesion with epoxy, and partially aligns the CNTs. Such microstructural changes result in superior mechanical performance and heat transfer in the composites compared to their mold-casted counterparts. This work demonstrates the advantages of 3D printing over traditional fabrication methods, beyond the ability to rapidly fabricate complex architectures, to achieve improved processing dynamics for fabricating CNT-polymer nanocomposites with better structural and functional properties.
comments
Fetching comments Fetching comments
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا