Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userHelical Undulator Based on Partial Redistribution of Uniform Magnetic Field
72
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
A new type of helical undulator based on redistribution of magnetic field of a solenoid by ferromagnetic helix has been proposed and studied both in theory and experiment. Such undulators are very simple and efficient for promising sources of coherent spontaneous THz undulator radiation from dense electron bunches formed in laser-driven photo-injectors.
rate research
Read More
The positron source of the International Linear Collider is based on a superconducting helical undulator passed by the high-energy electron beam to generate photons which hit a conversion target. Since the photons are circularly polarized the resulting positron beam is polarized. At ILC250, the full undulator is needed to produce the required number of positrons. To keep the power deposition in the undulator walls below the acceptable limit of 1W/m, photon masks must be inserted in the undulator line. The photon mask design requires a detailed study of the power deposition in the walls and masks. This paper describes the power deposition in the undulator wall due to synchrotron radiation.
Tabrizi et al. [physics/0701342] discuss the feasibility of an electron-based crystal undulator (e-CU) by planar channeling of 50 GeV electrons through a periodically bent crystal. We show that their scheme is not feasible. First, their undulator parameter is K >> 1 always, which destroys photon interference. Second, they overestimate the electron dechanneling length in e-CU by an order of magnitude, which shortens the number N of e-CU periods from 5-15 (as they hope) to just 1-2. This kills their e-CU concept again. We made first simulation of electron channeling in undulated crystal and conclude that an electron-based crystal wiggler is feasible with wiggler strength K=10 and number of periods N=2.
The undulator line of the Shanghai soft X-ray Free-electron Laser facility (SXFEL) has very tight tolerances on the straightness of the electron beam trajectory. However, the beam trajectory cannot meet the lasing requirements due to the influence of beam position, launch angle and quadrupole offsets. Traditional mechanical alignment can only control the rms of offsets to about 100 $mu$m, which is far from reaching the requirement. Further orbit correction can be achieved by beam-based alignment (BBA) method based on electron energy variations. K modulation is used to determine whether the beam passes through the quadrupole magnetic center, and the Dispersion-Free Steering (DFS) method is used to calculate the offsets of quadrupole and BPM. In this paper, a detailed result of simulation is presented which demonstrates that the beam trajectory with rms and standard deviation ($sigma$) less than 10 $mu$m can be obtained.
The design of the positron source for the International Linear Collider (ILC) is still under consideration. The baseline design plans to use the electron beam for the positron production before it goes to the IP. The high-energy electrons pass a long helical undulator and generate an intense circularly polarized photon beam which hits a thin conversion target to produce $e^+e^-$ pairs. The resulting positron beam is longitudinally polarized which provides an important benefit for precision physics analyses. In this paper the status of the design studies is presented with focus on ILC250. In particular, the target design and cooling as well as issues of the optical matching device are important for the positron yield. Some possibilities to optimize the system are discussed.
Free Electron Lasers (FEL) are commonly regarded as the potential key application of laser wakefield accelerators (LWFA). It has been found that electron bunches exiting from state-of-the-art LWFAs exhibit a normalized 6-dimensional beam brightness comparable to those in conventional linear accelerators. Effectively exploiting this beneficial beam property for LWFA-based FELs is challenging due to the extreme initial conditions particularly in terms of beam divergence and energy spread. Several different approaches for capturing, reshaping and matching LWFA beams to suited undulators, such as bunch decompression or transverse-gradient undulator schemes, are currently being explored. In this article the transverse gradient undulator concept will be discussed with a focus on recent experimental achievements.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
