Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userWake Measurements of a Dechirper Jaw with Non-Zero Tilt Angle
109
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The RadiaBeam/SLAC dechirper at the Linac Coherent Light Source (LCLS) is being used as a fast kicker, by inducing transverse wakefields, to e.g. facilitate Fresh-slice, two-color laser operation. The dechirper jaws are independently adjustable at both ends, and it is difficult to avoid leaving residual (longitudinal) tilt in them during set-up. In this report we develop a model independent method of removing unknown tilt in a jaw. In addition, for a short uniform bunch passing by a single dechirper plate, we derive an explicit analytical formula for the transverse wake kick as function of average plate offset and tilt angle. We perform wake kick measurements for the different dechirper jaws of the RadiaBeam/SLAC dechirper, and find that the agreement between measurement and theory is excellent.
rate research
Read More
The RadiaBeam/SLAC dechirper, a structure consisting of pairs of flat, metallic, corrugated plates, %a corrugated structure in flat geometry, has been installed just upstream of the undulators in the Linac Coherent Light Source (LCLS). As a dechirper, with the beam passing between the plates on axis, longitudinal wakefields are induced that can remove unwanted energy chirp in the beam. However, with the beam passing off axis, strong transverse wakes are also induced. This mode of operation has already been used for the production of intense, multi-color photon beams using the Fresh-Slice technique, and is being used to develop a diagnostic for attosecond bunch length measurements. Here we measure, as function of offset, the strength of the transverse wakefields that are excited between the two plates, and also for the case of the beam passing near to a single plate. We compare with analytical formulas from the literature, and find good agreement. This report presents the first systematic measurements of the transverse wake strength in a dechirper, one that has been excited by a bunch with the short pulse duration and high energy found in an X-ray free electron laser.
We have performed Joule power loss calculations for a flat dechirper. We have considered the configurations of the beam on-axis between the two plates---for chirp control---and for the beam especially close to one plate---for use as a fast kicker. Our calculations use a surface impedance approach, one that is valid when corrugation parameters are small compared to aperture (the perturbative parameter regime). In our model we ignore effects of field reflections at the sides of the dechirper plates, and thus expect the results to underestimate the Joule losses. The analytical results were also tested by numerical, time-domain simulations. We find that most of the wake power lost by the beam is radiated out to the sides of the plates. For the case of the beam passing by a single plate, we derive an analytical expression for the broad-band impedance, and---in Appendix B---numerically confirm recently developed, analytical formulas for the short-range wakes. While our theory can be applied to the LCLS-II dechirper with large gaps, for the nominal apertures we are not in the perturbative regime and the reflection contribution to Joule losses is not negligible. With input from computer simulations, we estimate the Joule power loss (assuming bunch charge of 300 pC, repetition rate of 100 kHz) is 21~W/m for the case of two plates, and 24 W/m for the case of a single plate.
In previous work [1] general expressions, valid for arbitrary bunch lengths, were derived for the wakefields of corrugated structures with flat geometry, such as is used in the RadiaBeam/LCLS dechirper. However, the bunch at the end of linac-based X-ray FELs--like the LCLS--is extremely short, and for short bunches the wakes can be considerably simplified. In this work, we first derive analytical approximations to the short-range wakes. These are generalized wakes, in the sense that their validity is not limited to a small neighborhood of the symmetry axis, but rather extends to arbitrary transverse offsets of driving and test particles. The validity of these short-bunch wakes holds not only for the corrugated structure, but rather for any flat structure whose beam-cavity interaction can be described by a surface impedance. We use these wakes to obtain, for a short bunch passing through a dechirper: estimates of the energy loss as function of gap, the transverse kick as function of beam offset, the slice energy spread increase, and the emittance growth. In the Appendix, a more accurate derivation--than is found in [1]--of the arbitrary bunch length wakes is performed; we find full agreement with the earlier results, provided the bunches are short compared to the dechirper gap, which is normally the regime of interest. [1] K. Bane and G. Stupakov, Phys. Rev. ST Accel. Beams 18, 034401(2015).
We give formulas for the longitudinal, transverse, and quad point charge wakes for a short bunch of electrons passing by one plate of a flat dechirper.
When a resistive feedback and single-bunch wake act together, it is known that some head-tail modes may become unstable even without space charge. This feedback-wake instability, FWI, modified by space charge to a certain degree, is shown to have a special single-maximum increasing- dropping pattern with respect to the gain. Also, at sufficiently large Coulomb and wake fields, as well as the feedback gain, a new type of transverse mode-coupling instability is shown to take place, 3FMCI, when head-to-tail amplified positive modes couple and the growth rate saturates with the gain.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
