Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userDARHT Axis 1 Compensation Can D-dot Calibration
40
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We detail the calibration of the D-dot probes used on the Los Alamos National Laboratory DARHT Axis 1 LIA compensation cans (CCs). We hope this will serve not only as a record of this calibration, but also as a guide on how to perform similar calibrations on other systems where D-dots are deployed. Although a simple measurement, its difficulty lies in the fact that the same geometry used when fielded must be used during calibration, the ultimate goal being to measure the capacitance between the probe sensor and the component whose voltage one intends to measure. Because of its linearity with voltage, this can be done at a lower voltage than during fielding, the only caveat being that this lower voltage pulse must still provide enough signal to noise. After a brief summary of our results, we include a description of a compensation can, the D-dot probe and its operation. We then provide 3D simulation results of the capacitance of this probe to the high voltage bushing under test inside of the compensation can. Finally, we describe our calibration setup and discuss our results.
rate research
Read More
An all solid-state kicker modulator for the Dual-Axis Radiographic Hydrodynamic Test facility (DARHT-2) has been designed and tested. This kicker modulator uses multiple solid-state modules stacked in an inductive-adder configuration where the energy is switched into each section of the adder by a parallel array of MOSFETs. The modulator features very fast rise and fall times, pulse width agility and a high pulse-repetition rate in burst mode. The modulator can drive a 50* cable with voltages up to 20 kV and can be easily configured for either positive or negative polarity. The presentation will include test data collected from both the ETA II accelerator kicker and resistive dummy loads.
RADMON is a small radiation monitor designed and assembled by students of the University of Turku and the University of Helsinki. It is flown on-board Aalto-1, a 3-unit CubeSat in low Earth orbit at about 500 km altitude. The detector unit of the instrument consists of two detectors, a Si solid-state detector and a CsI(Tl) scintillator, and utilizes the textDelta{E}-E technique to determine the total energy and species of each particle hitting the detector. We present the results of the on-ground and in-flight calibration campaigns of the instrument, as well as the characterization of its response through extensive simulations within the Geant4 framework. The overall energy calibration margin achieved is about 5%. The full instrument response to protons and electrons is presented and the issue of proton contamination of the electron channels is quantified and discussed.
We measure the detection efficiency of single-photon detectors at wavelengths near 851 nm and 1533.6 nm. We investigate the spatial uniformity of one free-space-coupled single-photon avalanche diode and present a comparison between fusion-spliced and connectorized fiber-coupled single-photon detectors. We find that our expanded relative uncertainty for a single measurement of the detection efficiency is as low as 0.70 % for fiber-coupled measurements at 1533.6 nm and as high as 1.78 % for our free-space characterization at 851.7 nm. The detection-efficiency determination includes corrections for afterpulsing, dark count, and count-rate effects of the single-photon detector with the detection efficiency interpolated to operation at a specified detected count rate.
Monitoring the dose delivered during proton and carbon ion therapy is still a matter of research. Among the possible solutions, several exploit the measurement of the single photon emission from nuclear decays induced by the irradiation. To fully characterize such emission the detectors need development, since the energy spectrum spans the range above the MeV that is not traditionally used in medical applications. On the other hand, a deeper understanding of the reactions involving gamma production is needed in order to improve the physic models of Monte Carlo codes, relevant for an accurate prediction of the prompt-gamma energy spectrum.This paper describes a calibration technique tailored for the range of energy of interest and reanalyzes the data of the interaction of a 80MeV/u fully stripped carbon ion beam with a Poly-methyl methacrylate target. By adopting the FLUKA simulation with the appropriate calibration and resolution a significant improvement in the agreement between data and simulation is reported.
We report the operation of a cold-atom inertial sensor which continuously captures the rotation signal. Using a joint interrogation scheme, where we simultaneously prepare a cold-atom source and operate an atom interferometer (AI) enables us to eliminate the dead times. We show that such continuous operation improves the short-term sensitivity of AIs, and demonstrate a rotation sensitivity of $100 text{nrad.s}^{-1}.text{Hz}^{-1/2}$ in a cold-atom gyroscope of $11 text{cm}^2$ Sagnac area. We also demonstrate a rotation stability of $1 text{nrad.s}^{-1}$ at $10^4$ s of integration time, which establishes the record for atomic gyroscopes. The continuous operation of cold-atom inertial sensors will enable to benefit from the full sensitivity potential of large area AIs, determined by the quantum noise limit.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
