Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userA versatile scanning photocurrent mapping system to characterize optoelectronic devices based on 2D materials
77
0
0.0
(
0
)
Added by
Riccardo Frisenda Dr.
Publication date
2017
fields
Physics
and research's language is
English
Ask ChatGPT about the research
No Arabic abstract
The investigation of optoelectronic devices based on two-dimensional materials and their heterostructures is a very active area of investigation with both fundamental and applied aspects involved. We present a description of a home-built scanning photocurrent microscope that we have designed and developed to perform electronic transport and optical measurements of two-dimensional materials based devices. The complete system is rather inexpensive (<10000 EUR) and it can be easily replicated in any laboratory. To illustrate the setup we measure current-voltage characteristics, in dark and under global illumination, of an ultra-thin PN junction formed by the stacking of an n-doped few-layer MoS2 flake onto a p-type MoS2 flake. We then acquire scanning photocurrent maps and by mapping the short circuit current generated in the device under local illumination we find that at zero bias the photocurrent is generated mostly in the region of overlap between the n-type and p-type flakes.
rate research
Read More
Optical spectroscopy techniques such as differential reflectance and transmittance have proven to be very powerful techniques to study 2D materials. However, a thorough description of the experimental setups needed to carry out these measurements is lacking in the literature. We describe a versatile optical microscope setup to carry out differential reflectance and transmittance spectroscopy in 2D materials with a lateral resolution of ~1 micron in the visible and near-infrared part of the spectrum. We demonstrate the potential of the presented setup to determine the number of layers of 2D materials and to characterize their fundamental optical properties such as excitonic resonances. We illustrate its performance by studying mechanically exfoliated and chemical vapor-deposited transition metal dichalcogenide samples.
Two-dimensional (2D) materials exhibit a number of improved mechanical, optical, electronic properties compared to their bulk counterparts. The absence of dangling bonds in the cleaved surfaces of these materials allows combining different 2D materials into van der Waals heterostructures to fabricate p-n junctions, photodetectors, 2D-2D ohmic contacts that show unexpected performances. These intriguing results are regularly summarized in comprehensive reviews. A strategy to tailor their properties even further and to observe novel quantum phenomena consists in the fabrication of superlattices whose unit cell is formed either by two dissimilar 2D materials or by a 2D material subjected to a periodical perturbation, each component contributing with different characteristics. Furthermore, in a 2D materials-based superlattice, the interlayer interaction between the layers mediated by van der Waals forces constitutes a key parameter to tune the global properties of the superlattice. The above-mentioned factors reflect the potential to devise countless combinations of van der Waals 2D materials based superlattices. In the present feature article, we explain in detail the state-of-the-art of 2D materials-based superlattices and we describe the different methods to fabricate them, classified as vertical stacking, intercalation with atoms or molecules, moire patterning, strain engineering and lithographic design. We also aim to highlight some of the specific applications for each type of superlattices.
We review recent progress on spins and magnetism in 2D materials including graphene, transition metal dichalcogenides, and 2D magnets. We also discuss challenges and prospects for the future of spintronics with 2D van der Waals heterostructures.
The high mechanical strength and excellent flexibility of 2D materials such as graphene are some of their most important properties [1]. Good flexibility is key for exploiting 2D materials in many emerging technologies, such as wearable electronics, bioelectronics, protective coatings and composites [1] and recently bending has been suggested as a route to tune electronic transport behaviour [2]. For virtually all crystalline materials macroscopic deformation is accommodated by the movement of dislocations and through the formation of twinning defects [3]; it is the geometry of the resulting microstructure that largely determines the mechanical and electronic properties. Despite this, the atomic microstructure of 2D materials after mechanical deformation has not been widely investigated: only by understanding these deformed microstructures can the resulting properties be accurately predicted and controlled. In this paper we describe the different structural features that can form as a result of bending in van der Waals (vdW) crystals of 2D materials. We show that twin boundaries, an important class of crystal defect, are delocalised by several nm and not atomically sharp as has been assumed for over half a century [4]. In addition, we demonstrate that different classes of microstructure are present in the deformed material and can be predicted from just the atomic structure, bend angle, and flake thickness. We anticipate that this new knowledge of the deformation structure for 2D materials will provide foundations for tailoring transport behaviour[2], mechanical properties, liquid-phase [5,6] and scotch-tape exfoliation [7,8], and crystal growth.
Collective modes of doped two-dimensional crystalline materials, namely graphene, MoS$_2$ and phosphorene, both monolayer and bilayer structures, are explored using the density functional theory simulations together with the random phase approximation. The many-body dielectric functions of the materials are calculated using an {it ab initio} based model involving material-realistic physical properties. Having calculated the electron energy-loss, we calculate the collective modes of each material considering the in-phase and out-of-phase modes for bilayer structures. Furthermore, owing to many band structures and intreband transitions, we also find high-energy excitations in the systems. We explain that the material-specific dielectric function considering the polarizability of the crystalline material such as MoS$_2$ are needed to obtain realistic plasmon dispersions. For each material studied here, we find different collective modes and describe their physical origins.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
