Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMagnetic and Thermal Transport Properties of Permanent Magnets with Anisotropic Grain Structure
68
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Nanostructured permanent magnets are gaining increasing interest and importance for applications such as generators and motors. Thermal management is a key concern since performance of permanent magnets decreases with temperature. We investigated the magnetic and thermal transport properties of rare-earth free nanostructured SrFe12O19 magnets produced by the current activated pressure assisted densification. The synthesized magnets have aligned grains such that their magnetic easy axis is perpendicular to their largest surface area to maximize their magnetic performance. The SrFe12O19 magnets have fine grain sizes in the cross-plane direction and substantially larger grain sizes in the in-plane direction. It was found that this microstructure results in approximately a factor of two higher thermal conductivity in the in-plane direction, providing an opportunity for effective cooling. The phonons are the dominant heat carriers in this type of permanent magnets near room temperature. Temperature and direction dependent thermal conductivity measurements indicate that both Umklapp and grain boundary scattering are important in the in-plane direction, where the characteristic grain size is relatively large, while grain boundary scattering dominates the cross-plane thermal transport. The investigated nano/microstructural design strategy should translate well to other material systems and thus have important implications for thermal management of nanostructured permanent magnets.
rate research
Read More
We report the results of an experimental study of thermal and magnetic properties of nanostructured ferrimagnetic iron oxide composites with graphene and graphite fillers synthesized via the current activated pressure assisted densification. The thermal conductivity was measured using the laser-flash and transient plane source techniques. It was demonstrated that addition of 5 wt. % of equal mixture of graphene and graphite flakes to the composite results in a factor of x2.6 enhancement of the thermal conductivity without significant degradation of the saturation magnetization. The microscopy and spectroscopic characterization reveal that sp2 carbon fillers preserve their crystal structure and morphology during the composite processing. The strong increase in the thermal conductivity was attributed to the excellent phonon heat conduction properties of graphene and graphite. The results are important for energy and electronic applications of the nanostructured permanent magnets.
We aim at combining high coercivity magnetic nanowires in a polymer matrix in a view to fabricate rare--earth free bonded magnets. In particular, our aim is to fabricate anisotropic materials by aligning the wires in the polymer matrix. We have explored the different parameters of the fabrication process in order to produce a material with the best possible magnetic properties. We show that the choice of a proper solvent allows obtaining stable nanowire suspensions. The length and the type of the polymer chains play also an important role. Smaller chains ($M_w < 10000$) provide better magnetization results. The magnetic field applied during the casting of the material plays also a role and should be of the order of a fraction of a tesla. The local order of the nanowires in the matrix has been characterized by TEM and Small Angle Neutron Scattering. The correlation between the local order of the wires and the magnetic properties is discussed. Materials with coercivity $mu_0 H_c$ up to 0.70 $T$ at room temperature have been obtained.
Ti-substituted perovskites, La0.7Sr0.3Mn1-xTixO3, with x between 0 to 0.20, were investigated by neutron diffraction, magnetization, electric resistivity, and magnetoresistance (MR) measurements. All samples show a rhombohedral structure (space group R3c) from 10 K to room temperature. At room temperature, the cell parameters a, c and the unit cell volume increase with increasing Ti content. However, at 10 K, the cell parameter a has a maximum value for x = 0.10, and decreases for x greater than 0.10, while the unit cell volume remains nearly constant for x greater than 0.10. The average (Mn,Ti)-O bond length increases up to x=0.15, and the (Mn,Ti)-O-(Mn,Ti) bond angle decreases with increasing Ti content to its minimum value at x=0.15 at room temperature. Below the Curie temperature T_C, the resistance exhibits metallic behavior for the x _ 0.05 samples. A metal (semiconductor) to insulator transition is observed for the x_ 0.10 samples. A peak in resistivity appears below T_C for all samples, and shifts to a lower temperature as x increases. The substitution of Mn by Ti decreases the 2p-3d hybridization between O and Mn ions, reduces the bandwidth W, and increases the electron-phonon coupling. Therefore, the TC shifts to a lower temperature and the resistivity increases with increasing Ti content. A field-induced shift of the resistivity maximum occurs at x less than or equal to 0.10. The maximum MR effect is about 70% for La0.7Sr0.3Mn0.8Ti0.2O3. The separation of TC and the resistivity maximum temperature Tmax enhances the MR effect in these compounds due to the weak coupling between the magnetic ordering and the resistivity as compared with La0.7Sr0.3MnO3.
Pinning-type magnets maintaining high coercivity, i.e. the ability to sustain magnetization, at high temperature are at the core of thriving clean-energy technologies. Among these, Sm2Co17-based magnets are excellent candidates owing to their high-temperature stability. However, despite decades of efforts to optimize the intragranular microstructure, the coercivity currently only reaches 20~30% of the theoretical limits. Here, the roles of the grain-interior nanostructure and the grain boundaries in controlling coercivity are disentangled by an emerging magneto-electric approach. Through hydrogen charging/discharging by applying voltages of only ~ 1 V, the coercivity is reversibly tuned by an unprecedented value of ~ 1.3 T. In situ magneto-structural measurements and atomic-scale tracking of hydrogen atoms reveal that the segregation of hydrogen atoms at the grain boundaries, rather than the change of the crystal structure, dominates the reversible and substantial change of coercivity. Hydrogen lowers the local magnetocrystalline anisotropy and facilitates the magnetization reversal starting from the grain boundaries. Our study reveals the previously neglected critical role of grain boundaries in the conventional magnetisation-switching paradigm, suggesting a critical reconsideration of strategies to overcome the coercivity limits in permanent magnets, via for instance atomic-scale grain boundary engineering.
We investigated thermal properties of the epoxy-based composites with a high loading fraction - up to f=45 vol.% - of the randomly oriented electrically conductive graphene fillers and electrically insulating boron nitride fillers. It was found that both types of the composites revealed a distinctive thermal percolation threshold at the loading fraction f>20 vol.%. The graphene loading required for achieving the thermal percolation was substantially higher than the loading for the electrical percolation. Graphene fillers outperformed boron nitride fillers in the thermal conductivity enhancement. It was established that thermal transport in composites with the high filler loading, above the thermal percolation threshold, is dominated by heat conduction via the network of percolating fillers. Unexpectedly, we determined that the thermal transport properties of the high loading composites were influenced strongly by the cross-plane thermal conductivity of the quasi-two-dimensional fillers. The obtained results shed light on the debated mechanism of the thermal percolation, and facilitate the development of the next generation of the efficient thermal interface materials for electronic applications.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
