Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userStorage-ring Electron Cooler for Relativistic Ion Beams
253
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Application of electron cooling at ion energies above a few GeV has been limited due to reduction of electron cooling efficiency with energy and difficulty in producing and accelerating a high-current high-quality electron beam. A high-current storage-ring electron cooler offers a solution to both of these problems by maintaining high cooling beam quality through naturally-occurring synchrotron radiation damping of the electron beam. However, the range of ion energies where storage-ring electron cooling can be used has been limited by low electron beam damping rates at low ion energies and high equilibrium electron energy spread at high ion energies. This paper reports a development of a storage ring based cooler consisting of two sections with significantly different energies: the cooling and damping sections. The electron energy and other parameters in the cooling section are adjusted for optimum cooling of a stored ion beam. The beam parameters in the damping section are adjusted for optimum damping of the electron beam. The necessary energy difference is provided by an energy recovering SRF structure. A prototype linear optics of such storage-ring cooler and initial tracking simulations are presented and some potential issues such as coherent synchrotron radiation and beam break up are discussed.
rate research
Read More
The Recycler Electron Cooler (REC) was the first cooler working at a relativistic energy (gamma = 9.5). It was successfully developed in 1995-2004 and was in operation at Fermilab in 2005-2011, providing cooling of antiprotons in the Recycler ring. After introducing the physics of electron cooling and the REC system, this paper describes measurements carried out to tune the electron beam and optimize its cooling properties. In particular, we discuss the cooling strategy adopted for maximizing the collider integrated luminosity.
Streaking of photoelectrons with optical lasers has been widely used for temporal characterization of attosecond extreme ultraviolet pulses. Recently, this technique has been adapted to characterize femtosecond x-ray pulses in free-electron lasers with the streaking imprinted by farinfrared and Terahertz (THz) pulses. Here, we report successful implementation of THz streaking for time-stamping of an ultrashort relativistic electron beam of which the energy is several orders of magnitude higher than photoelectrons. Such ability is especially important for MeV ultrafast electron diffraction (UED) applications where electron beams with a few femtosecond pulse width may be obtained with longitudinal compression while the arrival time may fluctuate at a much larger time scale. Using this laser-driven THz streaking technique, the arrival time of an ultrashort electron beam with 6 fs (rms) pulse width has been determined with 1.5 fs (rms) accuracy. Furthermore, we have proposed and demonstrated a non-invasive method for correction of the timing jitter with femtosecond accuracy through measurement of the compressed beam energy, which may allow one to advance UED towards sub-10 fs frontier far beyond the ~100 fs (rms) jitter.
Photons, electrons, and their interplay are at the heart of photonic devices and modern instruments for ultrafast science [1-10]. Nowadays, electron beams of the highest intensity and brightness are created by photoemission with short laser pulses, and then accelerated and manipulated using GHz radiofrequency electromagnetic fields. The electron beams are utilized to directly map photoinduced dynamics with ultrafast electron scattering techniques, or further engaged for coherent radiation production at up to hard X-ray wavelengths [11-13]. The push towards improved timing precision between the electron beams and pump optical pulses though, has been stalled at the few tens of femtosecond level, due to technical challenges with synchronizing the high power rf fields with optical sources. Here, we demonstrate attosecond electron metrology using laser-generated single-cycle THz radiation, which is intrinsically phase locked to the optical drive pulses, to manipulate multi-MeV relativistic electron beams. Control and single-shot characterization of bright electron beams at this unprecedented level open up many new opportunities for atomic visualization.
We report on an injection feedback scheme for the ThomX storage ring project. ThomX is a 50-MeV-electron accelerator prototype which will use Compton backscattering in a storage ring to generate a high flux of hard X-rays. Given the slow beam damping (in the ring), the injection must be performed with high accuracy to avoid large betatron oscillations. A homemade analytic code is used to compute the corrections that need to be applied before the beam injection to achieve a beam position accuracy of a few hundred micrometers in the first beam position monitors (BPMs). In order to do so the code needs the information provided by the rings diagnostic devices. The iterative feedback system has been tested using MadX simulations. Our simulations show that a performance that matches the BPMs accuracy can be achieved in less than 50 iterations in all cases. Details of this feedback algorithm, its efficiency and the simulations are discussed.
High power, relativistic electron beams from energy recovery linacs have great potential to realize new experimental paradigms for pioneering innovation in fundamental and applied research. A major design consideration for this new generation of experimental capabilities is the understanding of the halo associated with these bright, intense beams. In this Letter, we report on measurements performed using the 100 MeV, 430 kWatt CW electron beam from the energy recovery linac at the Jefferson Laboratorys Free Electron Laser facility as it traversed a set of small apertures in a 127 mm long aluminum block. Thermal measurements of the block together with neutron measurements near the beam-target interaction point yielded a consistent understanding of the beam losses. These were determined to be 3 ppm through a 2 mm diameter aperture and were maintained during a 7 hour continuous run.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
