Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userInvestigation of heat release in the targets during irradiation by ion beams
114
0
0.0
(
0
)
Added by
Aleksey Rusetskiy S
Publication date
2015
fields
Physics
and research's language is
English
Ask ChatGPT about the research
No Arabic abstract
The DD-reaction is investigated and the heat emission off the targets during their irradiation with ion beams is studied at the HELIS ion accelerator at LPI. The heat emission is observed to be significantly higher in the case of irradiation of the Ti/TiO2:Dx-targets by a D+ beam, as compared to the H+ and Ne+ beams. Furthermore, it depends on the concentration of deuterium in the target and current density of the deuteron beam.
rate research
Read More
High electronic excitations in radiation of metallic targets with swift heavy ion beams at the coulomb barrier play a dominant role in the damaging processes of some metals. The inelastic thermal spike model was developed to describe tracks in materials and is applied in this paper to some systems beams/targets employed recently in some nuclear physics experiments. Taking into account the experimental conditions and the approved electron-phonon coupling factors, the results of the calculation enable to interpret the observation of the fast deformation of some targets.
Ion-ion collisions at relativistic energies have been shown recently to be a promising technique for the production of hypernuclei. In this article, we further investigate the production of light $Lambda$ hypernuclei by use of a hybrid dynamical model, cascade-coalescence followed by Fermi breakup. The predictions are then compared with the available experimental data. The dependence of the production cross section upon the beam energy, beam mass number as well as different projectile-target combinations is investigated. In particular, we evaluate the yields and signal-over-background ratio in the invariant-mass spectrum for carbon projectiles impinging on hydrogen and carbon targets and various coincidence conditions in the experiment using the theoretical calculation as an input. It is found that comparing with carbon target, hydrogen target also leads to sizable hypernuclear yields, even for exotic species, and the hydrogen target could improve significantly signal-over-background ratio in some hypernuclear invariant mass studies.
We have produced in the Nuclear Physics Center in Lisbon thin film self-supported targets of Ag, LiF/Ag and CaF$_2$/Ag by a high vacuum resistance evaporation method. The production setup, materials, methods, characterization and results are described.
We have developed a method for achieving excellent resolving power in in-flight particle identification of radioactive isotope (RI) beams at the BigRIPS fragment separator at the RIKEN Nishina Center RI Beam Factory (RIBF). In the BigRIPS separator, RI beams are identified by their atomic number Z and mass-to-charge ratio A/Q which are deduced from the measurements of time of flight (TOF), magnetic rigidity (Brho) and energy loss (delta-E), and delivered as tagged RI beams to a variety of experiments including secondary reaction measurements. High A/Q resolution is an essential requirement for this scheme, because the charge state Q of RI beams has to be identified at RIBF energies such as 200-300 MeV/nucleon. By precisely determining the Brho and TOF values, we have achieved relative A/Q resolution as good as 0.034% (root-mean-square value). The achieved A/Q resolution is high enough to clearly identify the charge state Q in the Z versus A/Q particle identification plot, where fully-stripped and hydrogen-like peaks are very closely located. The precise Brho determination is achieved by refined particle trajectory reconstruction, while a slew correction is performed to precisely determine the TOF value. Furthermore background events are thoroughly removed to improve reliability of the particle identification. In the present paper we present the details of the particle identification scheme in the BigRIPS separator. The isotope separation in the BigRIPS separator is also briefly introduced.
The general properties needed in targets (sources) for high precision, high accuracy measurements are reviewed. The application of these principles to the problem of developing targets for the Fission TPC is described. Longer term issues, such as the availability of actinide materials, improved knowledge of energy losses and straggling and the stability of targets during irradiation are also discussed.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
