Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userShot noise of a quantum dot measured with GHz stub impedance matching
113
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The demand for a fast high-frequency read-out of high impedance devices, such as quantum dots, necessitates impedance matching. Here we use a resonant impedance matching circuit (a stub tuner) realized by on-chip superconducting transmission lines to measure the electronic shot noise of a carbon nanotube quantum dot at a frequency close to 3 GHz in an efficient way. As compared to wide-band detection without impedance matching, the signal to noise ratio can be enhanced by as much as a factor of 800 for a device with an impedance of 100 k$Omega$. The advantage of the stub resonator concept is the ease with which the response of the circuit can be predicted, designed and fabricated. We further demonstrate that all relevant matching circuit parameters can reliably be deduced from power reflectance measurements and then used to predict the power transmission function from the device through the circuit. The shot noise of the carbon nanotube quantum dot in the Coulomb blockade regime shows an oscillating suppression below the Schottky value of $2eI$, as well an enhancement in specific regions.
rate research
Read More
As an alternative to Buttikers dephasing lead model, we examine a dephasing stub. Both models are phenomenological ways to introduce decoherence in chaotic scattering by a quantum dot. The difference is that the dephasing lead opens up the quantum dot by connecting it to an electron reservoir, while the dephasing stub is closed at one end. Voltage fluctuations in the stub take over the dephasing role from the reservoir. Because the quantum dot with dephasing lead is an open system, only expectation values of the current can be forced to vanish at low frequencies, while the outcome of an individual measurement is not so constrained. The quantum dot with dephasing stub, in contrast, remains a closed system with a vanishing low-frequency current at each and every measurement. This difference is a crucial one in the context of quantum algorithms, which are based on the outcome of individual measurements rather than on expectation values. We demonstrate that the dephasing stub model has a parameter range in which the voltage fluctuations are sufficiently strong to suppress quantum interference effects, while still being sufficiently weak that classical current fluctuations can be neglected relative to the nonequilibrium shot noise.
We report the realization of a bonded-bridge on-chip superconducting coil and its use in impedance-matching a highly ohmic quantum dot (QD) to a $rm{3~GHz}$ measurement setup. The coil, modeled as a lumped-element $LC$ resonator, is more compact and has a wider bandwidth than resonators based on coplanar transmission lines (e.g. $lambda/4$ impedance transformers and stub tuners) at potentially better signal-to-noise ratios. In particular for measurements of radiation emitted by the device, such as shot noise, the 50$times$ larger bandwidth reduces the time to acquire the spectral density. The resonance frequency, close to 3.25 GHz, is three times higher than that of the one previously reported wire-bonded coil. As a proof of principle, we fabricated an $LC$ circuit that achieves impedance-matching to a $rm{sim 15~kOmega}$ load and validate it with a load defined by a carbon nanotube QD of which we measure the shot noise in the Coulomb blockade regime.
Integrating nano-scale objects, such as single molecules or carbon nanotubes, into impedance transformers and performing radio-frequency measurements allows for high time-resolution transport measurements with improved signal-to-noise ratios. The realization of such transformers implemented with superconducting transmission lines for the 2-10 GHz frequency range is presented here. Controlled electromigration of an integrated gold break junction is used to characterize a 6 GHz impedance matching device. The real part of the RF impedance of the break junction extracted from microwave reflectometry at a maximum bandwidth of 45 MHz of the matching circuit is in good agreement with the measured direct current resistance.
We study shot noise in tunneling current through a double quantum dot connected to two electric leads. We derive two master equations in the occupation-state basis and the eigenstate basis to describe the electron dynamics. The approach based on the occupation-state basis, despite widely used in many previous studies, is valid only when the interdot coupling strength is much smaller than the energy difference between the two dots. In contrast, the calculations using the eigenstate basis are valid for an arbitrary interdot coupling. We show that the master equation in the occupation-state basis includes only the low-order terms with respect to the interdot coupling compared with the more accurate master equation in the eigenstate basis. Using realistic model parameters, we demonstrate that the predicted currents and shot-noise properties from the two approaches are significantly different when the interdot coupling is not small. Furthermore, properties of the shot noise predicted using the eigenstate basis successfully reproduce qualitative features found in a recent experiment.
We study electron transport through a quantum dot, connected to non-magnetic leads, in a magnetic field. A super-Poissonian electron noise due to the effects of both interacting localized states and dynamic channel blockade is found when the Coulomb blockade is partially lifted. This is sharp contrast to the sub-Poissonian shot noise found in the previous studies for a large bias voltage, where the Coulomb blockade is completely lifted. Moreover, we show that the super-Poissonian shot noise can be suppressed by applying an electron spin resonance (ESR) driving field. For a sufficiently strong ESR driving field strength, the super-Poissonian shot noise will change to be sub-Poissonian.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
