Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMechanical analysis of a $beta=0.09 $ 162.5MHz taper HWR cavity
112
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
One superconducting taper-type half-wave resonator (HWR) with frequency of 162.5MHz, b{eta} of 0.09 has been developed at Peking University, which is used to accelerate high current proton ($sim$ 100mA) and $D^{+}$($sim$ 50mA). The radio frequency (RF) design of the cavity has been accomplished. Herein, we present the mechanical analysis of the cavity which is also an important aspect in superconducting cavity design. The frequency shift caused by bath helium pressure and Lorenz force, and the tuning by deforming the cavity along the beam axis will be analyzed in this paper.
rate research
Read More
A superconducting half-wave resonator (HWR) of frequency=162.5 MHz and {beta}=0.09 has been developed at Institute of Modern Physics. Mechanical stability of the low beta HWR cavity is a big challenge in cavity design and optimization. The mechanical deformations of a radio frequency superconducting cavity could be a source of instability, both in continues wave(CW) operation or in pulsed mode. Generally, the lower beta cavities have stronger Lorentz force detuning than that of the higher beta cavities. In this paper, a basic design consideration in the stiffening structure for the detuning effect caused by helium pressure and Lorentz force has been presented. The mechanical modal analysis has been investigated with finite element method(FEM). Based on these considerations, a new stiffening structure has been promoted for the HWR cavity. The computation results concerning the frequency shift show that the low beta HWR cavity with new stiffening structure has low frequency sensitivity coefficient, Lorentz force detuning coefficient KL and stable mechanical property.
A single gap, 352 MHz superconducting reentrant cavity for 5-100 MeV beams has been designed and it is presently under construction. This development is being done in the framework of a 30 mA proton linac project for nuclear waste transmutation. Mechanical, cryogenic and rf design characteristics of such cavities will be described.
Model-independent analysis (MIA) methods are generally useful for analysing complex systems in which relationships between the observables are non-trivial and noise is present. Principle Component Analysis (PCA) is one of MIA methods allowing to isolate components in the input data graded to their contribution to the variability of the data. In this publication we show how the PCA can be applied to digitised signals obtained from a cavity beam position monitor (CBPM) system on the example of a 3-cavity test system installed at the Accelerator Test Facility 2 (ATF2) at KEK in Japan. We demonstrate that the PCA based method can be used to extract beam position information, and matches conventional techniques in terms of performance, while requiring considerably less settings and data for calibration.
Superconducting linacs are capable of producing intense, stable, high-quality electron beams that have found widespread applications in science and industry. The 9-cell 1.3-GHz superconducting standing-wave accelerating RF cavity originally developed for $e^+/e^-$ linear-collider applications [B. Aunes, {em et al.} Phys. Rev. ST Accel. Beams {bf 3}, 092001 (2000)] has been broadly employed in various superconducting-linac designs. In this paper we discuss the transfer matrix of such a cavity and present its measurement performed at the Fermilab Accelerator Science and Technology (FAST) facility. The experimental results are found to be in agreement with analytical calculations and numerical simulations.
Superconducting cavities with low RF frequencies and heavy damping of higher order modes (HOM) are desired for the main accelerator of High Energy Photon Source (HEPS), a 6 GeV synchrotron light source promising ultralow emittance currently under construction in Beijing. A compact 166.6 MHz superconducting cavity was proposed adopting a quarter-wave beta=1 geometry. Based on the successful development of a proof-of-principle cavity, a HOM-damped 166.6 MHz compact superconducting cavity was subsequently designed. A ferrite damper was installed on the beam pipe to reduce HOM impedance below the stringent threshold of coupled-bunch instabilities. Being compact, RF field heating on the cavity vacuum seal was carefully examined against quenching the NbTi flange. The cavity was later dressed with a helium vessel and the tuning mechanism was also realized. Excellent RF and mechanical properties were eventually achieved. Finally, the two-cavity string was designed to ensure smooth transitions among components and proper shielding of synchrotron light. This paper presents a complete design of a fully dressed HOM-damped low-frequency beta=1 superconducting cavity for HEPS.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
