Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userA high-precision mechanical absolute-rotation sensor
219
0
0.0
(
0
)
Added by
Krishna Venkateswara
Publication date
2014
fields
Physics
and research's language is
English
Ask ChatGPT about the research
No Arabic abstract
We have developed a mechanical absolute-rotation sensor capable of resolving ground rotation angle of less than 1 nrad$/sqrt{text{Hz}}$ above $30$ mHz and 0.2 nrad$/sqrt{text{Hz}}$ above $100$ mHz about a single horizontal axis. The device consists of a meter-scale beam balance, suspended by a pair of flexures, with a resonance frequency of 10.8 mHz. The center of mass is located 3 $mu$m above the pivot, giving an excellent horizontal displacement rejection of better than $3times10^{-5}$ rad/m. The angle of the beam is read out optically using a high-sensitivity autocollimator. We have also built a tiltmeter with better than 1 nrad$/sqrt{text{Hz}}$ sensitivity above 30 mHz. Co-located measurements using the two instruments allowed us to distinguish between background rotation signal at low frequencies and intrinsic instrument noise. The rotation sensor is useful for rotational seismology and for rejecting background rotation signal from seismometers in experiments demanding high levels of seismic isolation, such as Advanced LIGO.
rate research
Read More
The most common method to measure direct current high voltage (HV) down to the ppm-level is to use resistive high-voltage dividers. Such devices scale the HV into a range where it can be compared with precision digital voltmeters to reference voltages sources, which can be traced back to Josephson voltage standards. So far the calibration of the scale factors of HV dividers for voltages above 1~kV could only be done at metrology institutes and sometimes involves round-robin tests among several institutions to get reliable results. Here we present a novel absolute calibration method based on the measurement of a differential scale factor, which can be performed with commercial equipment and outside metrology institutes. We demonstrate that reproducible measurements up to 35~kV can be performed with relative uncertainties below $1cdot10^{-6}$. This method is not restricted to metrology institutes and offers the possibility to determine the linearity of high-voltage dividers for a wide range of applications.
Absolute distance measurement (ADM) over a long range has been studied intensely over the last several decades, due to its important applications in large-scale manufacturing and outer space explorations [1-5]. Traditional absolute distance measurements utilize detection of time-of-flight information, detection of phase shift, or a combination of the two [6-17]. In this paper, we present a novel scheme for high-precision ADM over a long range based on frequency detection by using two optoelectronic oscillators (OEO) to convert distance information to frequency information. By taking advantage of accumulative magnification theory, the absolute error of the measured distance is magnified by about 2*10E5 times, which makes the precision of the measured distance significantly improved. In our experiments, the maximum error is 1.5 um at the emulated ~6 km distance, including the drift error of about 1 um in the air path due to the change in environmental conditions. In addition, the measurable distance using this scheme could be further extended. The highest relative measurement precision is 2*10E10 in our current system while the actual relative measurement precision of our experimental system is limited by the variation of atmospheric conditions and is about 4*10E9.
A technique for establishing the total neutron rate of a highly-collimated monochromatic cold neutron beam was demonstrated using a method of an alpha-gamma counter. The method involves only the counting of measured rates and is independent of neutron cross sections, decay chain branching ratios, and neutron beam energy. For the measurement, a target of 10B-enriched boron carbide totally absorbed the neutrons in a monochromatic beam, and the rate of absorbed neutrons was determined by counting 478keV gamma rays from neutron capture on 10B with calibrated high-purity germanium detectors. A second measurement based on Bragg diffraction from a perfect silicon crystal was performed to determine the mean de Broglie wavelength of the beam to a precision of 0.024 %. With these measurements, the detection efficiency of a neutron monitor based on neutron absorption on 6Li was determined to an overall uncertainty of 0.058 %. We discuss the principle of the alpha-gamma method and present details of how the measurement was performed including the systematic effects. We also describe how this method may be used for applications in neutron dosimetry and metrology, fundamental neutron physics, and neutron cross section measurements.
Iteratively Re-weighted Least Squares (IRLS) were used to simulate the $L_p$-norm approximation of the ballistic trajectory in absolute gravimeters. Two iterations of the IRLS delivered sufficient accuracy of the approximation without a significant bias. The simulations were performed on different samplings and perturbations of the trajectory. For the platykurtic distributions of the perturbations, the $L_p$-approximation with $3<p<4$ was found to yield several times more precise gravity estimates compared to the standard least-squares. The simulation results were confirmed by processing real gravity observations performed at the excessive noise conditions.
We present first results from a number of experiments conducted on a 0.53 kg cylindrical dumbbell-shaped sapphire crystal. This is the first reported optomechanical experiment of this nature utilising a novel modification to the typical cylindrical architecture. Mechanical motion of the crystal structure alters the dimensions of the crystal, and the induced strain changes the permittivity. These two effects result in parametric frequency modulation of resonant microwave whispering gallery modes that are simultaneously excited within the crystal. A novel low-noise microwave readout system is implemented allowing extremely low noise measurements of this frequency modulation near our modes of interest, having a phase noise floor of -165 dBc/Hz at 100 kHz. Fine-tuning of the crystals suspension has allowed for the optimisation of mechanical quality factors in preparation for cryogenic experiments, with a value of Q=8 x 10^7 achieved at 127 kHz. This results in a Q x f product of 10^13, equivalent to the best measured values in a macroscopic sapphire mechanical system. Results are presented that demonstrate the excitation of mechanical modes via radiation pressure force, allowing an experimental method of determining the transducers displacement sensitivity df/dx, and calibrating the system. Finally, we demonstrate parametric back-action phenomenon within the system. These are all important steps towards the overall goal of the experiment; to cool a macroscopic device to the quantum ground state at millikelvin temperatures.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
