Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userSpiraling Beam Illumination Uniformity on Heavy Ion Fusion Target
120
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
A few percent wobbling-beam illumination nonuniformity is realized in heavy ion inertial confinement fusion (HIF) by a spiraling beam axis motion in the paper. So far the wobbling heavy ion beam (HIB) illumination was proposed to realize a uniform implosion in HIF. However, the initial imprint of the wobbling HIBs was a serious problem and introduces a large unacceptable energy deposition nonuniformity. In the wobbling HIBs illumination, the illumination nonuniformity oscillates in time and space. The oscillating-HIB energy deposition may contribute to the reduction of the HIBs illumination nonuniformity. The wobbling HIBs can be generated in HIB accelerators and the oscillating frequency may be several 100MHz-1GHz. Three-dimensional HIBs illumination computations presented here show that the few percent wobbling HIBs illumination nonuniformity oscillates successfully with the same wobbling HIBs frequency.
rate research
Read More
In inertial confinement fusion the target implosion non-uniformity is introduced by a driver beams illumination non-uniformity, a fuel target alignment error in a fusion reactor, the target fabrication defect, et al. For a steady operation of a fusion power plant the target implosion should be robust against the implosion non-uniformities. In this paper the requirement for the implosion uniformity is first discussed. The implosion uniformity should be less than a few percent. A study on the fuel hotspot dynamics is also presented and shows that the stagnating plasma fluid provides a significant enhancement of vorticity at the final stage of the fuel stagnation. Then non-uniformity mitigation mechanisms of the heavy ion beam (HIB) illumination are also briefly discussed in heavy ion inertial fusion (HIF). A density valley appears in the energy absorber, and the large-scale density valley also works as a radiation energy confinement layer, which contributes to a radiation energy smoothing. In HIF a wobbling heavy ion beam illumination was also introduced to realize a uniform implosion. In the wobbling HIBs illumination, the illumination non-uniformity oscillates in time and space on a HIF target. The oscillating-HIB energy deposition may contribute to the reduction of the HIBs illumination non-uniformity by its smoothing effect on the HIB illumination non-uniformity and also by a growth mitigation effect on the Rayleigh-Taylor instability.
In inertial fusion, one of scientific issues is to reduce an implosion non-uniformity of a spherical fuel target. The implosion non-uniformity is caused by several factors, including the driver beam illumination non-uniformity, the Rayleigh-Taylor instability (RTI) growth, etc. In this paper we propose a new control method to reduce the implosion non-uniformity; the oscillating implosion acceleration dg(t) is created by pulsating and dephasing heavy ion beams (HIBs) in heavy ion inertial fusion (HIF). The dg(t) would reduce the RTI growth effectively. The original concept of the non- uniformity control in inertial fusion was proposed in (Kawata, et al., 1993). In this paper it was found that the pulsating and dephasing HIBs illumination provide successfully the controlled dg(t) and that dg(t) induced by the pulsating HIBs reduces well the implosion non-uniformity. Consequently the pulsating HIBs improve a pellet gain remarkably in HIF.
Heavy ion inertial fusion (HIF) energy would be one of promising energy resources securing our future energy in order to sustain our human life for centuries and beyond. The heavy ion beam (HIB) has remarkable preferable features to release the fusion energy in inertial confinement fusion: in particle accelerators HIBs are generated with a high driver efficiency of ~ 30-40%, and the HIB ions deposit their energy inside of materials. Therefore, a requirement for the fusion target energy gain is relatively low, that would be ~50-70 to operate a HIF fusion reactor with the standard energy output of 1GW of electricity. The HIF reactor operation frequency would be ~10~15 Hz or so. Several-MJ HIBs illuminate a fusion fuel target, and the fuel target is imploded to about a thousand times of the solid density. Then the DT fuel is ignited and burned. The HIB ion deposition range would be ~0.5-1 mm or so depending on the material. Therefore, a relatively large density-scale length appears in the fuel target material. The large density-gradient-scale length helps to reduce the Rayleigh-Taylor (R-T) growth rate. The key merits in HIF physics are presented in the article toward our bright future energy resource.
The Code O-SUKI is an integrated 2-dimensional (2D) simulation program system for a fuel implosion, ignition and burning of a direct-drive nuclear-fusion pellet in heavy ion beam (HIB) inertial confinement fusion (HIF). The Code O-SUKI consists of the four programs of the HIB illumination and energy deposition program of OK3 (Comput. Phys. Commun. 181, 1332 (2010)), a Lagrangian fluid implosion program, a data conversion program, and an Euler fluid implosion, ignition and burning program. The OK3 computes the multi-HIBs irradiation onto a spherical fuel target. One HIB is divided into many beamlets in OK3. Each heavy ion beamlet deposits its energy along the trajectory in a deposition layer depending on the particle energy. The OK3 also has a function of a wobbling motion of the HIB axis oscillation, and the HIBs energy deposition spatial detail profile is obtained inside the energy absorber of the fuel target. The spherical target implosion 2D behavior is computed by the 2D Lagrangian fluid code coupled with OK3, until just before the void closure time of the fuel implosion. After that, all the data by the Lagrangian implosion code are converted to them for the Eulerian code. The fusion Deuterium (D)-Tritium (T) fuel and the inward moving heavy tamping material are imploded and deformed seriously at the stagnation phase. The Euler fluid code is appropriate to simulate the fusion fuel compression, ignition and burning. The Code O-SUKI 2D simulation system provides a capability to compute and to study the HIF target implosion dynamics.
In this paper a study on a fusion reactor core is presented in heavy ion inertial fusion (HIF), including the heavy ion beam (HIB) transport in a fusion reactor, a HIB interaction with a background gas, reactor cavity gas dynamics, the reactor gas backflow to the beam lines, and a HIB fusion reactor design. The HIB has remarkable preferable features to release the fusion energy in inertial fusion: in particle accelerators HIBs are generated with a high driver efficiency of ~30-40%, and the HIB ions deposit their energy inside of materials. Therefore, a requirement for the fusion target energy gain is relatively low, that would be ~50 to operate a HIF fusion reactor with a standard energy output of 1GW of electricity. In a fusion reactor the HIB charge neutralization is needed for a ballistic HIB transport. Multiple mechanical shutters would be installed at each HIB port at the reactor wall to stop the blast waves and the chamber gas backflow, so that the accelerator final elements would be protected from the reactor gas contaminant. The essential fusion reactor components are discussed in this paper.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
