Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userTermination control of NdGaO3 crystal surfaces by selective chemical etching
303
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
A chemical etching method was developed for (110) and (001) NdGaO3 single crystal substrates in order to obtain an atomically flat GaO2-x - terminated surface. Depending on the surface step density the substrates were etched in pH-controlled NH4F- or NH4Cl-based solutions, followed by an annealing step at temperatures of 800-1000oC, in air or in oxygen flow, in order to recrystallize the surface. Atomic Force Microscopy (AFM) and high-pressure Reflection High Energy Electron Diffraction (RHEED) were used to analyse the surface morphology of the samples after every treatment. Studies on the chemistry and characteristics of the terminating layer showed that the chemically etched NdGaO3 substrate surface has a GaO2-x termination and that the (110) and (001) NdGaO3 surfaces are characterized by a different free surface energy, which is lower for latter.
rate research
Read More
We study strain relaxation and surface damage of GaN nanopillar arrays fabricated using inductively coupled plasma (ICP) etching and post etch wet chemical treatment. We controlled the shape and surface damage of such nanopillar structures through selection of etching parameters. We compared different substrate temperatures and different chlorine-based etch chemistries to fabricate high quality GaN nanopillars. Room temperature photoluminescence and Raman scattering measurements were carried to study the presence of surface defect and strain relaxation on these nanostructures, respectively. We found that wet KOH etching can remove the side wall damages caused by dry plasma etching, leading to better quality of GaN nanopillars arrays. The Si material underneath the GaN pillars was removed by KOH wet etching, leaving behind a fine Si pillar to support the GaN structure. Substantial strain relaxations were observed in these structures from room temperature Raman spectroscopy measurements. Room temperature Photoluminescence spectroscopy shows the presence of whispering gallery modes from these the nano disks structures.
We use first-principles methods to investigate the adsorption of Cu, Pb, Ag, and Mg onto a H-terminated Si surface. We show that Cu and Pb can adsorb strongly while Ag and Mg are fairly inert. In addition, two types of adsorption states are seen to exist for Pb. We also study the clustering energetics of Cu and Pb on the surface and find that while Cu clusters eagerly, Pb may prefer to form only small clusters of a few atoms. This kind of behavior of impurities is incorporated in kinetic Monte Carlo simulations of wet etching of Si. The simulation results agree with experiments supporting the idea that micromasking by Cu clusters and Pb atoms is the mechanism through which these impurities affect the etching process.
Patterned graphene shows substantial potential for applications in future molecular-scale integrated electronics. Environmental effects are a critical issue in a single layer material where every atom is on the surface. Especially intriguing is the variety of rich chemical interactions shown by molecular oxygen with aromatic molecules. We find that O2 etching kinetics vary strongly with the number of graphene layers in the sample. Three-layer-thick samples show etching similar to bulk natural graphite. Single-layer graphene reacts faster and shows random etch pits in contrast to natural graphite where nucleation occurs at point defects. In addition, basal plane oxygen species strongly hole dope graphene, with a Fermi level shift of ~0.5 eV. These oxygen species partially desorb in an Ar gas flow, or under irradiation by far UV light, and readsorb again in an O2 atmosphere at room temperature. This strongly doped graphene is very different than graphene oxide made by mineral acid attack.
Although, poly(dimethylsiloxane) (PDMS) is a widely used material in numerous applications, such as micro- or nanofabrication, the method of its selective etching has not been known up to now. In this work authors present two methods of etching the pure, additive-free and cured PDMS as a positive resist material. To achieve the chemical modification of the polymer necessary for selective etching, energetic ions were used. We created 7 um and 45 um thick PDMS layers and patterned them by a focused proton microbeam with various, relatively large fluences. In this paper authors demonstrate that 30 wt% Potassium Hydroxide (KOH) or 30 wt% sodium hydroxide (NaOH) at 70 oC temperature etch proton irradiated PDMS selectively, and remove the chemically sufficiently modified areas. In case of KOH development, the maximum etching rate was approximately 3.5 um/minute and it occurs at about 7.5*10^15 ion*cm-2. In case of NaOH etching the maximum etching rate is slightly lower, 1.75 um/minute and can be found at the slightly higher fluence of 8.75*10^15 ion*cm-2. These results are of high importance since up to this time it has not been known how to develop the additive-free, cross-linked poly(dimethylsiloxane) in lithography as a positive tone resist material.
Atomically flat interfaces between ternary oxides have chemically different variants, depending on the terminating lattice planes of both oxides. Electronic properties change with the interface termination which affects, for instance, charge accumulation and magnetic interactions at the interface. Well-defined terminations have yet rarely been achieved for oxides of ABO3 type (with metals A, B). Here, we report on a strategy of thin film growth and interface characterization applied to fabricate the La0.7Sr0.3MnO3-SrRuO3 interface with controlled termination. Ultra-strong antiferromagnetic coupling between the ferromagnets occurs at the MnO2-SrO interface, but not for the other termination, in agreement with density functional calculations. X-ray magnetic circular dichroism measurements reveal coupled reversal of Mn and Ru magnetic moments at the MnO2-SrO interface. Our results demonstrate termination control of magnetic coupling across a complex oxide interface and provide a pathway for theoretical and experimental explorations of novel electronic interface states with engineered magnetic properties.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
