Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userReduction of coating thermal noise by using an etalon
245
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Reduction of coating thermal noise is a key issue in precise measurements with an optical interferometer. A good example of such a measurement device is a gravitational-wave detector, where each mirror is coated by a few tens of quarter-wavelength dielectric layers to achieve high reflectivity while the thermal-noise level increases with the number of layers. One way to realize the reduction of coating thermal noise, recently proposed by Khalili, is the mechanical separation of the first few layers from the rest so that a major part of the fluctuations contributes only little to the phase shift of the reflected light. Using an etalon, a Fabry-Perot optical resonator of a monolithic cavity, with a few coating layers on the front and significantly more on the back surface is a way to realize such a system without too much complexity, and in this paper we perform a thermal-noise analysis of an etalon using the Fluctuation-dissipation theorem with probes on both sides of a finite-size cylindrical mirror.
rate research
Read More
Thermal noise of a mirror is one of the limiting noise sources in the high precision measurement such as gravitational-wave detection, and the modeling of thermal noise has been developed and refined over a decade. In this paper, we present a derivation of coating thermal noise of a finite-size cylindrical mirror based on the fluctuation-dissipation theorem. The result agrees to a previous result with an infinite-size mirror in the limit of large thickness, and also agrees to an independent result based on the mode expansion with a thin-mirror approximation. Our study will play an important role not only to accurately estimate the thermal-noise level of gravitational-wave detectors but also to help analyzing thermal noise in quantum-measurement experiments with lighter mirrors.
Optical multilayer coatings of high-reflective mirrors significantly determine the properties of Fabry-Perot resonators. Thermal (Brownian) noise in these coatings produce excess phase noise which can seriously degrade the sensitivity of high-precision measurements with these cavities, in particular in laser gravitational-wave antennas (for example project LIGO), where at the current stage it is one of the main limiting factors. We present a method to calculate this effect accurately and analyze different strategies to diminish it by optimizing the coating. Traditionally this noise is calculated as if the beam is reflected from the surface of the mirror fluctuating due to the sums of the fluctuations of each layer. However the beam in fact penetrates a coating and Brownian expansion of the layers leads to dephasing of interference in the coating and consequently to additional change in reflected phase. Fluctuations in the thickness of a layer change the strain in the medium and hence due to photoelastic effect change the refractive index of this layer. This additional effect should be also considered. It is possible to make the noise smaller preserving the reflectivity by changing the total number of layers and thicknesses of high and low refractive ones. We show how this optimized coating may be constructed analytically rather then numerically as before. We also check the possibility to use internal resonant layers and optimized cap layer to decrease the thermal noise.
Thermal noise of a mirror is one of the most important issues in high precision measurements such as gravitational-wave detection or cold damping experiments. It has been pointed out that thermal noise of a mirror with multi-layer coatings can be reduced by mechanical separation of the layers. In this paper, we introduce a way to further reduce thermal noise by locking the mechanically separated mirrors. The reduction is limited by the standard quantum limit of control noise, but it can be overcome with a quantum-non-demolition technique, which finally raises a possibility of complete elimination of coating thermal noise.
In our previous research, simulation showed that a quantum locking scheme with homodyne detection in sub-cavities is effective in surpassing the quantum noise limit for Deci-hertz Interferometer Gravitational Wave Observatory (DECIGO) in a limited frequency range. This time we have simulated an optical spring effect in the sub-cavities of the quantum locking scheme. We found that the optimized total quantum noise is reduced in a broader frequency band, compared to the case without the optical spring effect significantly improving the sensitivity of DECIGO to the primordial gravitational waves.
Several large-scale interferometric gravitational-wave detectors use resonant arm cavities to enhance the light power in the interferometer arms. These cavities are based on different optical designs: One design uses wedged input mirrors to create additional optical pick-off ports for deriving control signals. The second design employs input mirrors without wedge and thus offers the possibility to use the etalon effect inside the input mirrors for tuning the finesse of the arm cavities. In this article we introduce a concept of maximized flexibility that combines both of these options, by featuring wedges at the input mirrors and using the etalon effect instead in the end mirrors. We present a design for the arm cavities of Advanced Virgo. We have used numerical simulations to derive requirements for the manufacturing accuracy of an end mirror etalon for Advanced Virgo. Furthermore, we give analytical approximations for the achievable tuning range of the etalon in dependence on the reflectance, the curvature and the orientation of the etalon back surface.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
