Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userPolymer nanoparticles to decrease thermal conductivity of phase change materials
128
0
0.0
(
0
)
Authors
Po Chapuis
Ask ChatGPT about the research
No Arabic abstract
Microparticles including paraffin are currently used for textiles coating in order to deaden thermal shocks. We will show that polymer nanoparticles embedded in those microsized capsules allow for decreasing the thermal conductivity of the coating and enhance the protection in the stationary regime. A reasonable volume fraction of polymer nanoparticles reduces the conductivity more than predicted by Maxwell mixing rules. Besides, measurements prove that the polymer nanoparticles do not affect the latent heat and even improve the phase change behaviour as well as the mechanical properties.
rate research
Read More
Thermally conductive polymers are of fundamental interest and can also be exploited in thermal management applications. Recent studies have shown stretched polymers can achieve high thermal conductivity. However, the transport mechanisms of heat in thermally conductive polymers have yet to be elucidated. Here we report a method for scalable fabrication of polyethylene films with a high thermal conductivity of 62 W/m-K. The achieved thermal conductivity is over two orders-of-magnitude greater than that of typical polymers (~0.1 W/m-K), and exceeds those of many metals and ceramics used as traditional heat conductors. Careful structural studies are carried out and reveal that the film consists of nanofibers with crystalline and amorphous regions. Contrary to conventional wisdom, we reveal the importance of the amorphous morphology in achieving such high thermal conductivity, rather than simply from enhancements in the degree of crystallinity and crystallite alignment. The amorphous phase reaches a remarkably high thermal conductivity of ~16 W/m-K. Even still, we identify that the presence of this amorphous phase is the dominant factor as the film thermal conductivity is still much lower than the predicted values for bulk single-crystal polyethylene (237 K/m-K). This work lays the foundation for the rational design and synthesis of thermally conductive polymers, and opens up new opportunities for advanced heat management, particularly when flexible, lightweight, chemically inert and electrically insulating thermal conductors are desired.
Quantifying the correlation between the complex structures of amorphous materials and their physical properties has been a long-standing problem in materials science. In amorphous Si, a representative covalent amorphous solid, the presence of a medium-range order (MRO) has been intensively discussed. However, the specific atomic arrangement corresponding to the MRO and its relationship with physical properties, such as thermal conductivity, remain elusive. Here, we solve this problem by combining topological data analysis, machine learning, and molecular dynamics simulations. By using persistent homology, we constructed a topological descriptor that can predict the thermal conductivity. Moreover, from the inverse analysis of the descriptor, we determined the typical ring features that correlated with both the thermal conductivity and MRO. The results provide an avenue for controlling the material characteristics through the topology of nanostructures.
We demonstrate here a controllable variation in the Casimir force. Changes in the force of up to 20% at separations of ~100 nm between Au and AgInSbTe (AIST) surfaces were achieved upon crystallization of an amorphous sample of AIST. This material is well known for its structural transformation, which produces a significant change in the optical properties and is exploited in optical data storage systems. The finding paves the way to the control of forces in nanosystems, such as micro- or nanoswitches by stimulating the phase change transition via localized heat sources.
The vibrational density of states (VDOS) of nanoclusters and nanocrystalline materials are derived from molecular-dynamics simulations using empirical tight-binding potentials. The results show that the VDOS inside nanoclusters can be understood as that of the corresponding bulk system compressed by the capillary pressure. At the surface of the nanoparticles the VDOS exhibits a strong enhancement at low energies and shows structures similar to that found near flat crystalline surfaces. For the nanocrystalline materials an increased VDOS is found at high and low phonon energies, in agreement with experimental findings. The individual VDOS contributions from the grain centers, grain boundaries, and internal surfaces show that, in the nanocrystalline materials, the VDOS enhancements are mainly caused by the grain-boundary contributions and that surface atoms play only a minor role. Although capillary pressures are also present inside the grains of nanocrystalline materials, their effect on the VDOS is different than in the cluster case which is probably due to the inter-grain coupling of the modes via the grain-boundaries.
The high breakdown current densities and resilience to scaling of the metallic transition metal trichalcogenides TaSe3 and ZrTe3 make them of interest for possible interconnect applications, and it motivates this study of their thermal conductivities and phonon properties. These crystals consist of planes of strongly bonded one-dimensional chains more weakly bonded to neighboring chains. Phonon dispersions and the thermal conductivity tensors are calculated using density functional theory combined with an iterative solution of the phonon Boltzmann transport equation. The phonon velocities and the thermal conductivities of TaSe3 are considerably more anisotropic than those of ZrTe3. The maximum LA velocity in ZrTe3 occurs in the cross-chain direction, and this is consistent with the strong cross-chain bonding that gives rise to large Fermi velocities in that direction. The thermal conductivities are similar to those of other metallic two-dimensional transition metal dichalcogenides. At room temperature, a significant portion of the heat is carried by the optical modes. In the low frequency range, the phonon lifetimes and mean free paths in TaSe3 are considerably shorter than those in ZrTe3. The shorter lifetimes in TaSe3 are consistent with the presence of lower frequency optical branches and zone-folding features in the acoustic branches that arise due to the doubling of the TaSe3 unit cell within the plane.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
