Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMethanofullerene Elongated Nanostructure Formation for Enhanced Organic Solar Cells
133
0
0.0
(
0
)
Added by
Roman Lopez-Sandoval
Publication date
2007
fields
Physics
and research's language is
English
Ask ChatGPT about the research
No Arabic abstract
Using transmission electron microscopy (TEM) and Z-contrast imaging we have demonstrated elongated nanostructure formation of fullerene derivative [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) within an organic host through annealing. The annealing provides an enhanced mobility of the PCBM molecules and, with good initial dispersion, allows for the formation of exaggerated grain growth within the polymer host. We have assembled these nanostructures within the regioregular conjugated polymer poly(3-hexylthiophene) (P3HT). This PCBM elongated nanostructure formation maybe responsible for the very high efficiencies observed, at very low loadings of PCBM (1:0.6, polymer to PCBM), in annealed photovoltaics. Moreover, our high resolution TEM and electron energy loss spectroscopy studies clearly show that the PCBM crystals remain crystalline and are unaffected by the 200-keV electron beam
rate research
Read More
The increase in the temperature of photovoltaic (PV) solar cells affects negatively their power conversion efficiency and decreases their lifetime. The negative effects are particularly pronounced in concentrator solar cells. Therefore, it is crucial to limit the PV cell temperature by effectively removing the excess heat. Conventional thermal phase change materials (PCMs) and thermal interface materials (TIMs) do not possess the thermal conductivity values sufficient for thermal management of the next generation of PV cells. In this paper, we report the results of investigation of the increased efficiency of PV cells with the use of graphene-enhanced TIMs. Graphene reveals the highest values of the intrinsic thermal conductivity. It was also shown that the thermal conductivity of composites can be increased via utilization of graphene fillers. We prepared TIMs with up to 6% of graphene designed specifically for PV cell application. The solar cells were tested using the solar simulation module. It was found that the drop in the output voltage of the solar panel under two-sun concentrated illumination can be reduced from 19% to 6% when graphene-enhanced TIMs are used. The proposed method can recover up to 75% of the power loss in solar cells.
Hybrid AMX3 perovskites (A=Cs, CH3NH3; M=Sn, Pb; X=halide) have revolutionized the scenario of emerging photovoltaic technologies. Introduced in 2009 by Kojima et al., a rapid evolution very recently led to 15% efficient solar cells. CH3NH3PbI3 has so far dominated the field, while the similar CH3NH3SnI3 has not been explored for photovoltaic applications, despite the reduced band-gap. Replacement of Pb by the more environment-friendly Sn would facilitate the large uptake of perovskite-based photovoltaics. Despite the extremely fast progress, the materials electronic properties which are key to the photovoltaic performance are relatively little understood. Here we develop an effective GW method incorporating spin-orbit coupling which allows us to accurately model the electronic, optical and transport properties of CH3NH3SnI3 and CH3NH3PbI3, opening the way to new materials design. The different CH3NH3SnI3 and CH3NH3PbI3 properties are discussed in light of their exploitation for solar cells, and found to be entirely due to relativistic effects.
We demonstrate a novel type of solar cell, one that uses fixed negative charges, formed at the interface of n-Si with Al2O3, to generate strong inversion at the Si surface by electrostatic repulsion. Built-in voltages of up to 755 mV are found at this interface. To be able to harness this large built-in voltage, we demonstrate a new photovoltaic device concept, where the photocurrent, generated in this inversion layer, is extracted via an inversion layer induced by a high work function PEDOT:PSS top contact, deposited on top of a passivating and dipole-inducing molecular monolayer. Results of the effect of the molecular monolayer on device performance yield open-circuit voltages of up to 550 mV for moderately doped Si, demonstrating the effectiveness of this contact structure in removing the Fermi level pinning that has hindered past efforts in developing this type of solar cell with n-type Si.
We propose an unexplored class of absorbing materials for high-efficiency solar cells: heterostructures of transition-metal oxides. In particular, LaVO_3 grown on SrTiO_3 has a direct band gap ~1.1 eV in the optimal range as well as an internal potential gradient, which can greatly help to separate the photo-generated electron-hole pairs. Furthermore, oxide heterostructures afford the flexibility to combine LaVO_3 with other materials such as LaFeO_3 in order to achieve even higher efficiencies with band-gap graded solar cells. We use density-functional theory to demonstrate these features.
In kesterite CZTSSe solar cell research, an asymmetric crystallization profile is often obtained after annealing, resulting in a bilayered or double-layered absorber. So far, only segregated pieces of research exist to characterize this double layer, its formation dynamics and its effect on the performance of devices. Here, we review the existing research on double-layered kesterites and evaluate the different mechanisms proposed. Using a cosputtering-based approach, we show that the two layers can differ significantly in morphology, composition and optoelectronic properties, and complement the results with a statistical dataset of over 850 individual CZTS solar cells. By reducing the absorber thickness from above 1000 nm to 300 nm, we show that the double layer segregation is alleviated. In turn, we see a progressive improvement in the device performance for lower thickness, which alone would be inconsistent with the known case of ultrathin CIGS solar cells. By comparing the results with CZTS grown on monocrystalline Si substrates, without a native Na supply, we show that the alkali metal supply does not determine the double layer formation, but merely reduces the threshold for its occurrence. Instead, we propose that the main formation mechanism is the early migration of Cu to the surface during annealing and formation of Cu2-xS phases, in a self-regulating process akin to the Kirkendall effect. We comment on the generality of the mechanism proposed, comparing our results to other synthesis routes, including our own in-house results from solution processing and pulsed laser deposition of sulfide and oxide-based targets. Although the double layer occurrence largely depends on the kesterite synthesis route, the common factors determining the double layer occurrence appear to be the presence of metallic Cu and/or a chalcogen deficiency in the precursor matrix.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
