A Monte Carlo simulation-based optimization of a multilayer 10B-RPC thermal neutron detector is performed targeting an increase in the counting rate capability while maintaining high (>50%) detection efficiency for thermal neutrons. The converter layer thicknesses of individual RPCs are optimized for several configurations of a detector containing a stack of 10 double gap RPCs. The results suggest that it is possible to reach a counting rate which is by a factor of eight higher in comparison to the rate of a detector with only one double-gap RPC. The effect of neutron scattering inside the detector contributing to the background is analyzed and design modifications of the first detector prototype, tested at neutron beam, are suggested.
HEIMDAL is a thermal powder diffractometer designed to operate at the European Spallation Source, worlds most intense neutron source. The detailed design of the instrument, which is expected to enter user operation in 2024/2025, assumes that the neutrons scattered by the powder under investigation will be collected with hundreds of large-area Multi-Wire Proportional Counters employing a $^{10}$B$_4$C-solid converter. The gas counters will consists of large active volumes and tapered trapezoidal shapes that allow for close packing into a cylindrical shell with high solid angle coverage. The whole detector will operate in an air environment within the shielding cave and provide signals with sensitivity for locating detection in three dimensions. This paper presents the results of a GEANT4 study of the baseline design for the HEIMDAL powder diffraction detector. The detector model was used to study key performance parameters such as detection efficiency and spatial resolution. The contribution of the detector to the resolving power of the instrument, one of the key figures-of-merit for powder diffractometers, was also investigated. Most of the simulation results reported in this work cannot be validated against a sufficiently similar physical reference until the first segment or module are constructed and tested with neutron beam. However, these results can help identify possible ways of optimising the detector design and provide the first glimpse into the expected performance of this technological approach.
The ambitious instrument suite for the future European Spallation Source whose civil construction started recently in Lund, Sweden, demands a set of diverse and challenging requirements for the neutron detectors. For instance, the unprecedented high flux expected on the samples to be investigated in neutron diffraction or reflectometry experiments requires detectors that can handle high counting rates, while the investigation of sub-millimeter protein crystals will only be possible with large-area detectors that can achieve a position resolution as low as 200 {mu}m. This has motivated an extensive research and development campaign to advance the state-of-the-art detector and to find new technologies that can reach maturity by the time the ESS will operate at full potential. This paper presents the key detector requirements for three of the Time-of-Flight diffraction instrument concepts selected by the Scientific Advisory Committee to advance into the phase of preliminary engineering design. We discuss the available detector technologies suitable for this particular instrument class and their major challenges. The detector technologies selected by the instrument teams to collect the diffraction patterns are briefly discussed. Analytical calculations, Monte-Carlo simulations, and real experimental data are used to develop a generic method to esti- mate the event rate in the diffraction detectors. The proposed approach is based upon conservative assumptions that use information and input parameters that reflect our current level of knowledge and understanding of the ESS project. We apply this method to make predictions for the future diffraction instruments, and thus provide additional information that can help the instrument teams with the optimisation of the detector designs.
We present the results of the measurements of the detection efficiency for a 4.7 r{A} neutron beam incident upon a detector incorporating a stack of up to five MultiWire Proportional Counters (MWPC) with Boron-coated cathodes. The cathodes were made of Aluminum and had a surface exhibiting millimeter-deep V-shaped grooves of 45{deg}, upon which the thin Boron film was deposited by DC magnetron sputtering. The incident neutrons interacting with the converter layer deposited on the sidewalls of the grooves have a higher capture probability, owing to the larger effective absorption film thickness. This leads to a higher overall detection efficiency for the grooved cathode when compared to a cathode with a flat surface. Both the experimental results and the predictions of the GEANT4 model suggests that a 5-counter detector stack with coated grooved cathodes has the same efficiency as a 7-counter stack with flat cathodes. The reduction in the number of counters in the stack without altering the detection efficiency will prove highly beneficial for large-area position-sensitive detectors for neutron scattering applications, for which the cost-effective manufacturing of the detector and associated readout electronics is an important objective. The proposed detector concept could be a technological option for one of the new chopper spectrometers and other instruments planned to be built at the future European Spallation Source in Sweden. These results with macrostructured cathodes generally apply not just to MWPCs but to other gaseous detectors as well.
The B(E2; Ii -> If) values for transitions in 71Ga and 73Ga were deduced from a Coulomb excitation experiment at the safe energy of 2.95 MeV/nucleon using post-accelerated beams of 71,73Ga at the REX-ISOLDE on-line isotope mass separator facility. The emitted gamma rays were detected by the MINIBALL-detector array and B(E2; Ii->If) values were obtained from the yields normalized to the known strength of the 2+ -> 0+ transition in the 120Sn target. The comparison of these new results with the data of less neutron-rich gallium isotopes shows a shift of the E2 collectivity towards lower excitation energy when adding neutrons beyond N = 40. This supports conclusions from previous studies of the gallium isotopes which indicated a structural change in this isotopical chain between N = 40 and N = 42. Combined with recent measurements from collinear laser spectroscopy showing a 1/2- spin and parity for the ground state, the extracted results revealed evidence for a 1/2-; 3/2- doublet near the ground state in 73 31Ga42 differing by at most 0.8 keV in energy.
We report on the investigation of the population mechanism for the 454-KeV level in 71Cu. This level was identified for the first time in a recent Coulomb excitation measurement with a radioactive beam of 71Cu. The selective nature of the Coulomb-excitation process as well as nuclear-structure considerations constrain the possible spin values for the newly observed state to Ipi=1/2-. A re-examination of the data set obtained in a beta-decay study at the LISOL separator revealed that this state is also populated in the decay of 71Ni, most probably by direct feeding from a newly identified 1/2- beta-decaying isomer having a T1/2=2.34(25) s. In this paper we investigate the proposed scenario by reanalyzing the beta-gamma and gamma-gamma coincidences obtained in the beta-decay study at LISOL.
The $B(E2;0^+to2^+)$ value in $^{68}$Ni has been measured using Coulomb excitation at safe energies. The $^{68}$Ni radioactive beam was post-accelerated at the ISOLDE facility (CERN) to 2.9 MeV/u. The emitted $gamma$ rays were detected by the MINIBALL detector array. A kinematic particle reconstruction was performed in order to increase the measured c.m. angular range of the excitation cross section. The obtained value of 2.8$^{+1.2}_{-1.0}$ 10$^2$ e$^2$fm$^4$ is in good agreement with the value measured at intermediate energy Coulomb excitation, confirming the low $0^+to2^+$ transition probability.
