اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدFabrication and spectral characterization of the porous dielectric THz waveguides using microstructured molding technique
189
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We report two novel fabrication techniques, as well as spectral transmission and propagation loss measurements of the subwavelength plastic wires with highly porous (up to 86%) and non-porous transverse geometries. The two fabrication techniques we describe are based on the microstructured molding approach. In one technique the mold is made completely from silica by stacking and fusing silica capillaries to the bottom of a silica ampoule. The melted material is then poured into the silica mold to cast the microstructured preform. Another approach uses microstructured mold made of plastic which is co-drawn with a cast preform. Material of the mold is then dissolved after fiber drawing. We also describe a novel THz-TDS setup with an easily adjustable optical path length, designed to perform cutback measurements using THz fibers of up to 50 cm in length. We find that while both porous and non-porous subwavelength fibers of the same outside diameter have low propagation losses (alpha leg 0.02cm-1), however, the porous fibers exhibit a much wider spectral transmission window and enable transmission at higher frequencies compared to the non-porous fibers. We then show that the typical bell-shaped transmission spectra of the subwavelengths fibers can be very well explained by the onset of material absorption loss at higher frequencies due to strong confinement of the modal fields in the material region of the fiber, as well as strong coupling loss at lower frequencies due to mismatch of the modal field diameter and a size of the gaussian-like beam of a THz source.
قيم البحث
اقرأ أيضاً
In this work, a novel infinity 3D printing technique is explored to fabricate continuous multi-meter-long low-loss near-zero dispersion suspended-core polypropylene fibers for application in terahertz (THz) communications. Particular attention is pai
d to process parameter optimization for 3D printing with low-loss polypropylene plastic. Three microstructured THz fibers were 3D printed using the standard and infinity 3D printers, and an in-depth theoretical and experimental comparison between the fibers were carried out. Transmission losses (by power) of 4.79 dB/m, 17.34 dB/m and 11.13 dB/m are experimentally demonstrated for the three fibers operating at 128 GHz. Signal transmission with BER far below the forward error correction limit (10-3) for the corresponding three fiber types of lengths of 2 m, 0.75 m and 1.6 m are observed, and an error-free transmission is realized at the bit rates up to 5.2 Gbps. THz imaging of the fiber near-field is used to visualize modal distributions and study optimal fiber excitation conditions. The ability of shielding the fundamental mode from the environment, mechanical robustness and ease of handling of thus developed effectively single-mode high optical performance fibers make them excellent candidates for upcoming fiber-assisted THz communications. Additionally, novel fused deposition modeling (FDM)-based infinity printing technique allows continuous fabrication of unlimited in length fibers of complex transverse geometries using advanced thermoplastic composites, which, in our opinion, is poised to become a key fabrication technique for advanced terahertz fiber manufacturing.
Waveguide characterization of dielectric materials is a convenient and broadband approach for measuring dielectric constant. In conventional microwave measurements, material samples are usually mechanically shaped to fit the waveguide opening and mea
sured in closed waveguides. This method is not practical for millimeter-wave and sub-millimeter-wave measurements where the waveguide openings become tiny, and it is rather difficult to shape the sample to exactly the same dimensions as the waveguide cross-section. In this paper, we present a method that allows one to measure arbitrarily shaped dielectric slabs that extend outside waveguides. In this method, the measured sample is placed between two waveguide flanges, creating a discontinuity. The measurement system is characterized as an equivalent Pi-circuit, and the circuit elements of the Pi-circuit are extracted from the scattering parameters. We have found that the equivalent shunt impedance of the measured sample is only determined by the material permittivity and is rather insensitive to the sample shape, position, sizes, and other structural details of the discontinuity. This feature can be leveraged for accurate measurements of permittivity. The proposed method is very useful for measuring the permittivity of medium-loss and high-loss dielectrics from microwave to sub-terahertz frequencies.
We present a practical approach to the numerical optimisation of the guiding properties of buried microstructured waveguides, which can be fabricated in a z-cut lithium niobate (LiNbO3) crystal by the method of direct femtosecond laser inscription. W
e demonstrate the possibility to extend the spectral range of low-loss operation of the waveguide into the mid-infrared region beyond 3{mu}m.
We study a plasmonic coupler involving backward (TM_01) and forward (HE_11) modes of dielectric waveguides embedded into infinite metal. The simultaneously achievable contradirectional energy flows and codirectional wavevectors in different channels
lead to a spectral gap, despite the absence of periodic structures along the waveguide. We demonstrate that a complete spectral gap can be achieved in a symmetric structure composed of four coupled waveguides.
Terahertz communications is a promising modality for future short-range point-to point wireless data transmission at rates up to terabit per second. A milestone towards this goal is the development of an integrated transmitter and receiver platforms
with high efficiency. One key enabling component is a planar waveguiding structure with wide bandwidth and low dispersion. This work proposes substrate-less all-dielectric waveguides cladded by an effective medium for low-loss and low dispersion terahertz transmission in broadband. This self-supporting structure is built solely into a single silicon wafer with air perforations to mitigate significant absorptions in metals and dielectrics at terahertz frequencies. The realized waveguides can cover the entire 260 to 400 GHz with single dominant modes in both orthogonal polarizations. The simulation shows that for the E_11^x mode the attenuation ranges from 0.003 to 0.024 dB/cm over the entire band, while it varies from 0.008 to 0.023 dB/cm for the E_11^y mode. Limited by the measurement setup, the maximum error-free data rate of 28 Gbit/s is experimentally achieved at 335 GHz on a 3-cm waveguide. We further demonstrate the transmission of uncompressed 4K-resolution video across this waveguide. This waveguide platform promises integration of diverse active and passive components. Thus, we can foresee it as a potential candidate for the future terahertz integrated circuits, in analogy to photonic integrated circuits at optical frequencies.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
