اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدHead-related transfer function measurements in a compartment fire
74
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The Personal Alert Safety System (PASS) is an alarm signal device carried by firefighters to help rescuers locate and extricate downed firefighters. A fire creates temperature gradients and inhomogeneous time-varying temperature, density, and flow fields that modify the acoustic properties of a room. To understand the effect of the fire on an alarm signal, experimental measurements of head-related transfer functions (HRTF) in a room with fire are presented in time and frequency domains. The results show that low frequency (<1000 Hz) modes in the HRTF increase in frequency and higher frequency modal structure weakens and becomes unstable in time. In the time domain, the time difference of arrival between the ears changes and becomes unstable over time. Both these effects could impact alarm signal detection and localization. Received level of narrowband tones is presented that shows the fire makes the received level of a source vary by >10 dB. All these effects could impact the detection and localization of the PASS alarm, and life safety consequences.
قيم البحث
اقرأ أيضاً
A compartment fire (a fire in a room or building) creates temperature gradients and inhomogeneous time-varying temperature, density, and flow fields. This work compared experimental measurements of the room acoustic impulse/frequency response in a ro
om with a fire to numerically modeled responses. The fire is modeled using Fire Dynamics Simulator (FDS). Acoustic modeling was performed using the temperature field computed by FDS. COMSOL Multiphysics was used for finite element acoustic modeling and Bellhop for ray-trace acoustics modeling. The results show that the fire causes wave-fronts to arrive earlier (due to the higher sound speed) and with more variation in the delay times (due to the sound speed perturbations). The frequency response shows that the modes are shifted up in frequency and high frequency (>2500 Hz) modes are significantly attenuated. Model results are compared with data and show good agreement in observed trends.
We previously reported on the complex permittivity and dc conductivity of waste-activated sludge. The measurements, spanning a frequency range of 3 MHz to 40 GHz, were made using an open-ended coaxial transmission line. Although this technique is wel
l established in the literature, we found that it was necessary to combine methods from several papers to use the open-ended coaxial probe to reliably characterize biological samples having a high dc conductivity. Here, we provide a set of detailed and practical guidelines that can be used to determine the permittivity and conductivity of biological samples over a broad frequency range. Due to the electrode polarization effect, low frequency measurements of conducting samples require corrections to extract the intrinsic electrical properties. We describe one practical correction scheme and verify its reliability using a control sample.
The spatial resolution achieved by recent synchrotron radiation microtomographs should be estimated from the modulation transfer function (MTF) on the micrometer scale. Step response functions of a synchrotron radiation microtomograph were determined
by the slanted edge method by using high-precision surfaces of diamond crystal and ion-milled aluminum wire. Tilted reconstruction was introduced to enable any edge to be used as the slanted edge by defining the reconstruction pixel matrix in an arbitrary orientation. MTFs were estimated from the step response functions of the slanted edges. The obtained MTFs coincided with MTF values estimated from square-wave patterns milled on the aluminum surface. Although x-ray refraction influences should be taken into account to evaluate MTFs, any flat surfaces with nanometer roughness can be used to determine the spatial resolutions of microtomographs.
An important problem to be solved in modeling head-related impulse responses (HRIRs) is how to individualize HRIRs so that they are suitable for a listener. We modeled the entire magnitude head-related transfer functions (HRTFs), in frequency domain,
for sound sources on horizontal plane of 37 subjects using principal components analysis (PCA). The individual magnitude HRTFs could be modeled adequately well by a linear combination of only ten orthonormal basis functions. The goal of this research was to establish multiple linear regression (MLR) between weights of basis functions obtained from PCA and fewer anthropometric measurements in order to individualize a given listeners HRTFs with his or her own anthropomety. We proposed here an improved individualization method based on MLR of weights of basis functions by utilizing 8 chosen out of 27 anthropometric measurements. Our objective experiments results show a superior performance than that of our previous work on individualizing minimum phase HRIRs and also better than similar research. The proposed individualization method shows that the individualized magnitude HRTFs could approximated well the the original ones with small error. Moving sound employing the reconstructed HRIRs could be perceived as if it was moving around the horizontal plane.
We present a laser frequency stabilization system that uses a transfer interferometer to stabilize slave lasers to a reference laser. Our implementation uses off-the-shelf optical components along with microcontroller-based digital feedback, and offe
rs a simple, flexible and robust way to stabilize multiple laser frequencies to better than 1 MHz.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
