اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدFast magneto-ionic switching of interface anisotropy using yttria-stabilized zirconia gate oxide
255
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Voltage control of interfacial magnetism has been greatly highlighted in spintronics research for many years, as it might enable ultra-low power technologies. Among few suggested approaches, magneto-ionic control of magnetism has demonstrated large modulation of magnetic anisotropy. Moreover, the recent demonstration of magneto-ionic devices using hydrogen ions presented relatively fast magnetization toggle switching, tsw ~ 100 ms, at room temperature. However, the operation speed may need to be significantly improved to be used for modern electronic devices. Here, we demonstrate that the speed of proton-induced magnetization toggle switching largely depends on proton-conducting oxides. We achieve ~1 ms reliable (> 103 cycles) switching using yttria-stabilized zirconia (YSZ), which is ~ 100 times faster than the state-of-the-art magneto-ionic devices reported to date at room temperature. Our results suggest further engineering of the proton-conducting materials could bring substantial improvement that may enable new low-power computing scheme based on magneto-ionics.
قيم البحث
اقرأ أيضاً
Additive manufacturing represents a revolution due to its unique capabilities for freeform fabrication of near net shapes with strong reduction of waste material and capital cost. These unfair advantages are especially relevant for expensive and ener
gy-demanding manufacturing processes of advanced ceramics such as Yttria-stabilized Zirconia, the state-of-the-art electrolyte in Solid Oxide Fuel Cell applications. In this study, self-supported electrolytes of yttria-stabilized zirconia have been printed by using a stereolithography three-dimensional printer. Printed electrolytes and complete cells fabricated with cathode and anode layers of lanthanum strontium manganite- and nickel oxide-yttria-stabilized zirconia composites, respectively, were electrochemical characterized showing full functionality. In addition, more complex configurations of the electrolyte have been printed yielding an increase of the performance entirely based on geometrical aspects. Complementary, a numerical model has been developed and validated as predictive tool for designing more advanced configurations that will enable highly performing and fully customized devices in the next future
Multilayered heterostructures of Ce0.85Sm0.15O2-delta and Y0.16Zr0.92O2-delta of a high crystallographic quality were fabricated on (001) - oriented MgO single crystal substrates. Keeping the total thickness of the heterostructures constant, the numb
er of ceria-zirconia bilayers was increased while reducing the thickness of each layer. At each interface Ce was found primarily in the reduced, 3+ oxidation state in a layer extending about 2 nm from the interface. Concurrently, the conductivity decreased as the thickness of the layers was reduced suggesting a progressive confinement of the charge transport along the YSZ layers. The comparative analysis of the in-plane electrical characterization suggests that the contribution to the total electrical conductivity of these interfacial regions is negligible. For the smallest layer thickness of 2 nm the doped ceria layers are electrically insulating and the ionic transport only occurs through the zirconia layers. This is explained in terms of a reduced mobility of the oxygen vacancies in the highly reduced ceria.
We have succeeded in growing epitaxial and highly stoichiometric films of EuO on yttria-stabilized cubic zirconia (YSZ) (001). The use of the Eu-distillation process during the molecular beam epitaxy assisted growth enables the consistent achievement
of stoichiometry. We have also succeeded in growing the films in a layer-by-layer fashion by fine tuning the Eu vs. oxygen deposition rates. The initial stages of growth involve the limited supply of oxygen from the YSZ substrate, but the EuO stoichiometry can still be well maintained. The films grown were sufficiently smooth so that the capping with a thin layer of aluminum was leak tight and enabled ex situ experiments free from trivalent Eu species. The findings were used to obtain recipes for better epitaxial growth of EuO on MgO (001).
Antiferromagnets offer spintronic device characteristics unparalleled in ferromagnets owing to their lack of stray fields, THz spin dynamics, and rich materials landscape. Microscopic imaging of aniferromagnetic domains is one of the key prerequisite
s for understading physical principles of the device operation. However, adapting common magnetometry techniques to the dipolar-field-free antiferromagnets has been a major challenge. Here we demonstrate in a collinear antiferromagnet a thermoelectric detection method by combining the magneto-Seebeck effect with local heat gradients generated by scanning far-field or near-field techniques. In a 20 nm epilayer of uniaxial CuMnAs we observe reversible 180 deg switching of the Neel vector via domain wall displacement, controlled by the polarity of the current pulses. We also image polarity-dependent 90 deg switching of the Neel vector in a thicker biaxial film, and domain shattering induced at higher pulse amplitudes. The antiferromagnetic domain maps obtained by our laboratory technique are compared to measurements by the established synchrotron microscopy using X-ray magnetic linear dichroism.
Microwave Pressing is a promising way to reduce microwave sintering temperatures and stabilize microwave powder materials processing. A multi-physics simulation was conducted of the regulated pressure-assisted microwave cavity. This simulation took i
nto consideration resonance phenomena and the nonlinear temperature-dependent material parameters of zirconia. The intrinsic behaviors of microwave systems and zirconia make the regulation of the microwave pressing difficult. However, the same phenomena can be used to activate flash sintering. Flash microwave sintering uses high electric fields of the resonant microwave profile, the Negative Temperature Behavior (NTC) of zirconia resistivity, and the mechanical pressure applied to the powder via a die compaction configuration. The resulting flash microwave pressing still needs improvement in terms of the processed material structure homogeneity, but it has the capacity to become the fastest sintering treatment as it allows room temperature activation where the total process time only takes a few seconds. In addition, this 10-20s processing technique has shown good potential for improving the transparency of alumina pre-sintered specimens.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
