اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدAutomodulations in Kerr-lens Modelocked Solid-State Lasers
151
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Nonstationary pulse regimes associated with self modulation of a Kerr-lens modelocked Ti:sapphire laser have been studied experimentally and theoretically. Such laser regimes occur at an intracavity group delay dispersion that is smaller or larger than what is required for stable modelocking and exhibit modulation in pulse amplitude and spectra at frequencies of several hundred kHz. Stabilization of such modulations, leading to an increase in the pulse peak power by a factor of ten, were accomplished by weakly modulating the pump laser with the self-modulation frequency. The main experimental observations can be explained with a round trip model of the fs laser taking into account gain saturation, Kerr lensing, and second- and third-order dispersion.
قيم البحث
اقرأ أيضاً
The theoretical calculation for nonlinear refractive index in Cr: ZnSe - active medium predicts the strong defocusing cascaded second-order nonlinearity within 2000 - 3000 nm spectral range. On the basis of this result the optimal cavity configuratio
n for Kerr-lens mode locking is proposed that allows to achieve a sub-100 fs pulse duration. The numerical simulations testify about strong destabilizing processes in the laser resulting from a strong self-phase modulation. The stabilization of the ultrashort pulse generation is possible due to spectral filtering that increases the pulse duration up to 300 fs.
Laser brightness is a measure of the ability to de- liver intense light to a target, and encapsulates both the energy content and the beam quality. High brightness lasers requires that both parameters be maximised, yet standard laser cavities do not
allow this. For example, in solid-state lasers multimode beams have a high energy content but low beam quality, while Gaussian modes have a small mode volume and hence low energy extraction, but in a good quality mode. Here we over- come this fundamental limitation and demonstrate an optimal approach to realising high brightness lasers. We employ intra- cavity beam shaping to produce a Gaussian mode that carries all the energy of the multimode beam, thus energy extraction and beam quality are simultaneously maximised. This work will have a significant influence on the design of future high brightness laser cavities.
We introduce a mechanism of stable spatiotemporal soliton formation in a multimode fiber laser. This is based on spatially graded dissipation, leading to distributed Kerr-lens mode-locking. Our analysis involves solutions of a generalized dissipative
Gross-Pitaevskii equation. This equation has a broad range of applications in nonlinear physics, including nonlinear optics, spatiotemporal patterns formation, plasma dynamics, and Bose-Einstein condensates. We demonstrate that careful control of dissipative and non-dissipative physical mechanisms results in the self-emergence of stable (2+1)-dimensional dissipative solitons. Achieving such a regime does not require the presence of any additional dissipative nonlinearities, such a mode-locker in a laser, or inelastic scattering in a Bose-Einstein condensate. Our method allows for stable energy (or mass) harvesting by coherent localized structures, such as ultrashort laser pulses or Bose-Einstein condensates.
Fast saturable absorbers (FSAs) play a critical role in stabilizing many passively modelocked lasers. The most commonly used averaged model to study these lasers is the Haus modelocking equation (HME) that includes a third-order nonlinear FSA. Howeve
r, it predicts a narrow region of stability that is inconsistent with experiments. To better replicate the laser physics, averaged laser models that include FSAs with higher-than-third-order nonlinearities have been introduced. Here, we compare three common FSA models to each other and to the HME using the recently-developed boundary tracking algorithms. The three FSA models are the cubic-quintic model, the sinusoidal model, and the algebraic model. We find that all three models predict the existence of a stable high-energy solution that is not present in the HME and have a much larger stable operating region. We also find that all three models predict qualitatively similar stability diagrams. We conclude that averaged laser models that include FSAs with higher-than-third-order nonlinearity should be used when studying the stability of passively modelocked lasers.
The polarization states of lasers are crucial issues both for practical applications and fundamental research. In general, they depend in a combined manner on the properties of the gain material and on the structure of the electromagnetic modes. In t
his paper, we address this issue in the case of solid-state organic lasers, a technology which enables to vary independently gain and mode properties. Different kinds of resonators are investigated: in-plane micro-resonators with Fabry-Perot, square, pentagon, stadium, disk, and kite shapes, and external vertical resonators. The degree of polarization P is measured in each case. It is shown that although TE modes prevail generally (P>0), kite-shaped micro-laser generates negative values for P, i.e. a flip of the dominant polarization which becomes mostly TM polarized. We at last investigated two degrees of freedom that are available to tailor the polarization of organic lasers, in addition to the pump polarization and the resonator geometry: upon using resonant energy transfer (RET) or upon pumping the laser dye to an higher excited state. We then demonstrate that significantly lower P factors can be obtained.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
