اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدReduced model for capillary breakup with thermal gradients: Predictions and computational validation
63
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
It was recently demonstrated that feeding a silicon-in-silica coaxial fibre into a flame$mathord{-}$imparting a steep silica viscosity gradient$mathord{-}$results in the formation of silicon spheres whose size is controlled by the feed speed [Gumennik et al., Nat.Commun. 4, 2216 (2013)]. A reduced model to predict the droplet size from the feed speed was then derived by Mowlavi et al. [Phys. Rev. Fluids. 4, 064003 (2019)], but large experimental uncertainties in the parameter values and temperature profile made quantitative validation of the model impossible. Here, we validate the reduced model against fully-resolved three-dimensional axisymmetric Stokes simulations using the exact same physical parameters and temperature profile. We obtain excellent quantitative agreement for a wide range of experimentally relevant feed speeds. Surprisingly, we also observe that the local capillary number at the breakup location remains almost constant across all feed speeds. Owing to its low computational cost, the reduced model is therefore a useful tool for designing future experiments.
قيم البحث
اقرأ أيضاً
Despite their fundamental and applied importance, a general model to predict the natural breakup length of steady capillary jets has not been proposed yet. In this work, we derive a scaling law with two universal constants to calculate that length as
a function of the liquid properties and operating conditions. These constants are determined by fitting the scaling law to a large set of experimental and numerical measurements, including previously published data. Both the experimental and numerical jet lengths conform remarkably well to the proposed scaling law. This law is explained in terms of the growth of perturbations excited by the jet breakup itself.
The motion of an air-fluid interface through an irregularly coated capillary is studied by analysing the Lucas-Washburn equation with a random capillary force. The pinning probability goes from zero to a maximum value, as the interface slows down. Un
der a critical velocity, the distribution of waiting times $tau$ displays a power-law tail $sim tau^{-2}$ which corresponds to a strongly intermittent dynamics, also observed in experiments. We elaborate a procedure to predict quantities of experimental interest, such as the average interface trajectory and the distribution of pinning lengths.
We develop a stochastic model for the velocity gradients dynamics along a Lagrangian trajectory. Comparing with different attempts proposed in the literature, the present model, at the cost of introducing a free parameter known in turbulence phenomen
ology as the intermittency coefficient, gives a realistic picture of velocity gradient statistics at any Reynolds number. To achieve this level of accuracy, we use as a first modelling step a regularized self-stretching term in the framework of the Recent Fluid Deformation (RFD) approximation that was shown to give a realistic picture of small scales statistics of turbulence only up to moderate Reynolds numbers. As a second step, we constrain the dynamics, in the spirit of Girimaji & Pope (1990), in order to impose a peculiar statistical structure to the dissipation seen by the Lagrangian particle. This probabilistic closure uses as a building block a random field that fulfils the statistical description of the intermittency, i.e. multifractal, phenomenon. To do so, we define and generalize to a statistically stationary framework a proposition made by Schmitt (2003). These considerations lead us to propose a non-linear and non-Markovian closed dynamics for the elements of the velocity gradient tensor. We numerically integrate this dynamics and observe that a stationary regime is indeed reached, in which (i) the gradients variance is proportional to the Reynolds number, (ii) gradients are typically correlated over the (small) Kolmogorov time scale and gradients norms over the (large) integral time scale (iii) the joint probability distribution function of the two non vanishing invariants $Q$ and $R$ reproduces the characteristic teardrop shape, (iv) vorticity gets preferentially aligned with the intermediate eigendirection of the deformation tensor and (v) gradients are strongly non-Gaussian and intermittent.
In global efforts to reduce harmful greenhouse gas emissions from the transport sector, novel bio-hybrid liquid fuels from renewable energy and carbon sources can be a major form of energy for future propulsion systems due to their high energy densit
y. A fundamental understanding of the spray and mixing performance of the new fuel candidates in combustion systems is necessary to design and develop the fuels for advanced combustion concepts. In the fuel design process, a large number of candidates is required to be screened to arrive at potential fuels for further detailed investigations. For such a screening process, three-dimensional (3D) simulation models are computationally too expensive and hence unfeasible. Therefore, in this paper, we present a fast, reduced-order model (ROM) for inert sprays. The model is based on the cross-sectionally averaged spray (CAS) model derived by Wan (1997) from 3D multiphase equations. The original model was first tested against a wide range of conditions and different fuels. The discrepancies between the CAS model and experimental data are addressed by integrating state-of-the-art breakup and evaporation models. A transport equation for vapor mass fraction is proposed, which is important for evaporation modeling. Furthermore, the model is extended to consider polydisperse droplets by modeling the droplet size distribution by commonly used presumed probability density functions, such as Rosin-Rammler, lognormal, and gamma distributions. The improved CAS model is capable of predicting trends in the macroscopic spray characteristics for a wide range of conditions and fuels. The computational cost of the CAS model is lower than the 3D simulation methods by up to 6 orders of magnitude depending on the method. This enables the model to be used not only for the rapid screening of novel fuel candidates, but also for other applications, where ROMs are useful.
We apply a previously developed asymptotic model (J. Fluid. Mech. 915, A133 (2021)) to study instabilities of free surface films of nanometric thickness on thermally conductive substrates in two and three spatial dimensions. While the specific focus
is on metal films exposed to laser heating, the model itself applies to any setup involving films on the nanoscale whose material parameters are temperature-dependent. For the particular case of metal films heated from above, an important aspect is that the considered heating is volumetric, since the absorption length of the applied laser pulse is comparable to the film thickness. In such a setup, absorption of thermal energy and film evolution are closely correlated and must be considered self-consistently. The asymptotic model allows for a significant simplification, which is crucial from both modeling and computational points of view, since it allows for asymptotically correct averaging of the temperature over the film thickness. We find that the properties of the thermally conductive substrate -- in particular its thickness and rate of heat loss -- play a critical role in controlling the film temperature and dynamics. The film evolution is simulated using efficient GPU-based simulations which, when combined with the developed asymptotic model, allow for fully nonlinear time-dependent simulations in large three-dimensional computational domains. In addition to uncovering the role of the substrate and its properties in determining the film evolution, one important finding is that, at least for the considered range of material parameters, strong in-plane thermal diffusion in the film results in negligible spatial variations of temperature, and the film evolution is predominantly influenced by temporal variation of film viscosity and surface tension (dictated by average film temperature), as well as thermal conductivity of the substrate.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
