ترغب بنشر مسار تعليمي؟ اضغط هنا

Spectrally Selective Solar Absorbers with High-temperature Insensitivity

108   0   0.0 ( 0 )
 نشر من قبل Yi Zheng
 تاريخ النشر 2020
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

It is of significance to incorporate spectral selectivity technology into solar thermal engineering, especially at high operational temperatures. This work demonstrates spectrally selective solar absorbers made of multilayer tungsten, silica, and alumina thin films that are angular insensitive and polarization-independent. An overall absorptance of 88.1% at solar irradiance wavelength, a low emittance of 7.0% at infrared thermal wavelength, and a high solar to heat efficiency of 79.9% are identified. Additionally, it shows the annealed samples maintain an extremely high absorption in solar radiation regime over at least 600 C and the solar absorbers after thermal annealing at 800 C still work well in a CSP system with an even high concentration factor of over 100.



قيم البحث

اقرأ أيضاً

Selective solar absorbers (SSAs) with high performance are the key to concentrated solar power systems. Optical metamaterials are emerging as a promising strategy to enhance selective photon absorption, however, the high-temperature resistance (>500C ) remains as one of the main challenges for their practical applications. Here, a multilayered metamaterial system (Al2O3/W/SiO2/W) based on metal-insulator-metal (MIM) resonance effect has been demonstrated with high solar absorptance over 92%, low thermal emittance loss below 6%, and significant high-temperature resistance: it has been proved that the optical performance remains 93.6% after 1-hour thermal annealing under ambient environment up to 500C, and 94.1% after 96-hour thermal cycle test at 400C, which is also confirmed by the microscopic morphology characterization. The spectral selectivity of fabricated SSAs is angular independent and polarization insensitive. Outdoor tests demonstrate that a peak temperature rise (193.5C) can be achieved with unconcentrated solar irradiance and surface abrasion resistance test yields that SSAs have a robust resistance to abrasion attack for engineering applications.
Spectrally selective solar absorbers (SSAs), harvesting sunlight into heat, are the key to the concentrated solar thermal systems. Current SSAs designs using photonic crystals, metamaterials, or cermets are either cost-inefficient or have limited app licability due to complicated nanofabrication methods and poor thermal stability at high temperatures. We present a scalable-manufactured blackbody cavity solar absorber design with nearly ideal properties. The unity solar absorptivity and nearly zero infrared emissivity allow for a stagnation temperature of 880C under 10 suns. The performance surpasses those state-of-the-art SSAs manufactured by nanofabrication methods. This design relies on traditional fabricating methods, such as machining, casting, and polishing. This makes it easy for large-scale industrial applications, and the blackbody cavity feature enables its fast-integration to existing concentrated solar thermal systems.
Titanium diboride (TiB2) is a low-density refractory material belonging to the family of ultra-high temperature ceramics (UHTCs). This paper reports on the production and microstructural and optical characterization of nearly fully dense TiB2, with p articular interest to its potential utilization as novel thermal solar absorber. Monolithic bulk samples are produced starting from elemental reactants by a two-step method consisting of the Self-propagating High-temperature Synthesis (SHS) followed by the Spark Plasma Sintering (SPS) of the resulting powders. The surface of obtained samples has-been characterized from the microstructural and topological points of view. The hemispherical reflectance spectrum has been measured from 0.3 to 15 um wavelength, to evaluate the potential of this material as solar absorber for future concentrating solar plants.
Various thin-film I$_2$-II-IV-VI$_4$ photovoltaic absorbers derived from kesterite Cu$_2$ZnSn(S,Se)$_4$ have been synthesized, characterized, and theoretically investigated in the past few years. The availability of this homogeneous materials dataset is an opportunity to examine trends in their defect properties and identify criteria to find new defect-tolerant materials in this vast chemical space. We find that substitutions on the Zn site lead to a smooth decrease in band tailing as the ionic radius of the substituting cation increases. Unfortunately, this substitution strategy does not ensure the suppression of deeper defects and non-radiative recombination. Trends across the full dataset suggest that Gaussian and Urbach band tails in kesterite-inspired semiconductors are two separate phenomena caused by two different antisite defect types. Deep Urbach tails are correlated with the calculated band gap narrowing caused by the (2I$_mathrm{II}$+IV$_mathrm{II}$) defect cluster. Shallow Gaussian tails are correlated with the energy difference between the kesterite and stannite polymorphs, which points to the role of (I$_mathrm{II}$+II$_mathrm{I}$) defect clusters involving Group IB and Group IIB atoms swapping across textit{different} cation planes. This finding can explain why textit{in-plane} cation disorder and band tailing are uncorrelated in kesterites. Our results provide quantitative criteria for discovering new kesterite-inspired photovoltaic materials with low band tailing.
We propose a frequency selective light trapping scheme that enables the creation of more visually-transparent and yet simultaneously more efficient semitransparent solar cells. A nanoparticle scattering layer and photonic stack back reflector create a selective trapping effect by total internal reflection within a medium, increasing absorption of IR light. We propose a strong frequency selective scattering layer using spherical TiO2 nanoparticles with radius of 255 nm and area density of 1.1% in a medium with index of refraction of 1.5. Using detailed numerical simulations for this configuration, we find that it is possible to create a semitransparent silicon solar cell that has a Shockley Queisser efficiency of 12.0%pm0.4% with a visible transparency of 60.2%pm1.3%, 13.3%pm1.3 more visibly-transparent than a bare silicon cell at the same efficiency.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا