اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدRegimes of Wetting Transitions on Superhydrophobic Textures Conditioned by Energy of Receding Contact Lines
121
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We discuss an evaporation-induced wetting transition on superhydrophobic stripes, and show that depending on the elastic energy of the deformed contact line, which determines the value of an instantaneous effective contact angle, two different scenarios occur. For relatively dilute stripes the receding angle is above 90$^circ$, and the sudden impalement transition happens due to an increase of a curvature of an evaporating drop. For dense stripes the slow impregnation transition commences when the effective angle reaches 90$^circ$ and represents the impregnation of the grooves from the triple contact line towards the drop center.
قيم البحث
اقرأ أيضاً
When a solid plate is withdrawn from a liquid bath, a receding contact line is formed where solid, liquid, and gas meet. Above a critical speed $U_{cr}$, a stationary contact line can no longer exist and the solid will eventually be covered completel
y by a liquid film. Here we show that the bifurcation diagram of this coating transition changes qualitatively, from discontinuous to continuous, when decreasing the inclination angle of the plate. We show that this effect is governed by the presence of capillary waves, illustrating that the large scale flow strongly effects the maximum speed of dewetting.
We study experimentally and discuss quantitatively the contact angle hysteresis on striped superhydrophobic surfaces as a function of a solid fraction, $phi_S$. It is shown that the receding regime is determined by a longitudinal sliding motion the d
eformed contact line. Despite an anisotropy of the texture the receding contact angle remains isotropic, i.e. is practically the same in the longitudinal and transverse directions. The cosine of the receding angle grows nonlinearly with $phi_S$, in contrast to predictions of the Cassie equation. To interpret this we develop a simple theoretical model, which shows that the value of the receding angle depends both on weak defects at smooth solid areas and on the elastic energy of strong defects at the borders of stripes, which scales as $phi_S^2 ln phi_S$. The advancing contact angle was found to be anisotropic, except as in a dilute regime, and its value is determined by the rolling motion of the drop. The cosine of the longitudinal advancing angle depends linearly on $phi_S$, but a satisfactory fit to the data can only be provided if we generalize the Cassie equation to account for weak defects. The cosine of the transverse advancing angle is much smaller and is maximized at $phi_Ssimeq 0.5$. An explanation of its value can be obtained if we invoke an additional energy due to strong defects in this direction, which is shown to be proportional to $phi_S^2$. Finally, the contact angle hysteresis is found to be quite large and generally anisotropic, but it becomes isotropic when $phi_Sleq 0.2$.
The dynamics of wetting and dewetting is largely determined by the velocity field near the contact lines. For water drops it has been observed that adding surfactant decreases the dynamic receding contact angle even at a concentration much lower than
the critical micelle concentration (CMC). To better understand why surfactants have such a drastic effect on drop dynamics, we constructed a dedicated a setup on an inverted microscope, in which an aqueous drop is held stationary while the transparent substrate is moved horizontally. Using astigmatism particle tracking velocimetry, we track the 3D displacement of the tracer particles in the flow. We study how surfactants alter the flow dynamics near the receding contact line of a moving drop for capillary numbers in the order of $10^{-6}$. Even for surfactant concentrations $c$ far below the critical micelle concentration ($c ll$ CMC) Marangoni stresses change the flow drastically. We discuss our results first in a 2D model that considers advective and diffusive surfactant transport and deduce estimates of the magnitude and scaling of the Marangoni stress from this. Modeling and experiment agree that a tiny gradient in surface tension of a few $mu N , m^{-1}$ is enough to alter the flow profile significantly. The variation of the Marangoni stress with the distance from the contact line suggests that the 2D advection-diffusion model has to be extended to a full 3D model. The effect is ubiquitous, since surfactant is present in many technical and natural dewetting processes either deliberately or as contamination.
The dynamics of the triple gas-liquid-solid contact line is analysed for the case where the gas is the saturated vapour corresponding to the liquid, like in the vapour bubble in boiling. It is shown that even small superheating (with respect to the s
aturation temperature) causes evaporation of the adsorption liquid film and the true triple contact is established. It is shown that the hydrodynamic contact line singularity cannot be relaxed with the Navier slip condition under such circumstances. Augmented with the second derivative slip condition is proposed to be applied. For the partial wetting conditions, a non-stationary contact line problem where the contact line motion is caused by evaporation or condensation is treated in the lubrication approximation in the vicinity of the contact line. High heat fluxes in this region require the transient heat conduction inside the heater to be accounted for. Two 2D problems, those of drop retraction with no phase change and of drop evaporation are solved and analysed as illustrations of the proposed approach.
We extend the Cahn-Landau-de Gennes mean field theory of binary mixtures to understand the wetting thermodynamics of a three phase system, that is in contact with an external surface which prefers one of the phases. We model the system using a phenom
enological free energy having three minima corresponding to low, intermediate and high density phases. By systematically varying the textit{(i)} depth of the central minimum, textit{(ii)} the surface interaction parameters, we explore the phase behavior, and wetting characteristics of the system across the triple point corresponding to three phase coexistence. We observe a non-monotonic dependence of the surface tension across the triple point that is associated with a complete to partial wetting transition. The methodology is then applied to study the wetting behaviour of a polymer-liquid crystal mixture in contact with a surface using a renormalised free energy. Our work provides a way to interrogate phase behavior and wetting transitions of biopolymers in cellular environments.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
