اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدMicroscopic diamond Solid-Immersion-Lenses fabricated around single defect ceneters by focussed ion beam milling
225
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Recent efforts to define microscopic solid-immersion-lenses (SIL) by focused ion beam milling into diamond substrates that are registered to a preselected single photon emitter are summarized. We show how we determine the position of a single emitter with at least 100 nm lateral and 500 nm axial accuracy, and how the milling procedure is optimized. The characteristics of a single emitter, a Nitrogen Vacancy (NV) center in diamond, are measured before and after producing the SIL and compared with each other. A count rate of 1.0 million counts per second is achieved with a $[111]$ oriented NV center.
قيم البحث
اقرأ أيضاً
We describe a technique for fabricating micro- and nano-structures incorporating fluorescent defects in diamond with a positional accuracy in the hundreds of nanometers. Using confocal fluorescence microscopy and focused ion beam (FIB) etching we fir
st locate a suitable defect with respect to registration marks on the diamond surface and then etch a structure using these coordinates. We demonstrate the technique here by etching an 8 micron diameter hemisphere positioned such that a single negatively charged nitrogen-vacancy defect lies at its origin. This type of structure increases the photon collection efficiency by removing refraction and aberration losses at the diamond-air interface. We make a direct comparison of the fluorescence photon count rate before and after fabrication and observe an 8-fold increase due to the presence of the hemisphere.
The efficiency of collecting photons from optically active defect centres in bulk diamond is greatly reduced by refraction and reflection at the diamond-air interface. We report on the fabrication and measurement of a geometrical solution to the prob
lem; integrated solid immersion lenses (SILs) etched directly into the surface of diamond. An increase of a factor of 10 was observed in the saturated count-rate from a single negatively charged nitrogen-vacancy (NV-) within a 5um diameter SIL compared with NV-s under a planar surface in the same crystal. A factor of 3 reduction in background emission was also observed due to the reduced excitation volume with a SIL present. Such a system is potentially scalable and easily adaptable to other defect centres in bulk diamond.
Diamond is a material of choice in the pursuit of integrated quantum photonic technologies. So far, the majority of photonic devices fabricated from diamond, are made from (100)-oriented crystals. In this work, we demonstrate a methodology for the fa
brication of optically-active membranes from (111)-oriented diamond. We use a liftoff technique to generate membranes, followed by chemical vapour deposition of diamond in the presence of silicon to generate homogenous silicon vacancy colour centers with emission properties that are superior to those in (100)-oriented diamond. We further use the diamond membranes to fabricate high quality microring resonators with quality factors exceeding ~ 3000. Supported by finite difference time domain calculations, we discuss the advantages of (111) oriented structures as building blocks for quantum nanophotonic devices.
We report on pulsed-laser induced generation of nitrogen-vacancy (NV) centers in diamond facilitated by a solid-immersion lens (SIL). The SIL enables laser writing at energies as low as 5.8 nJ per pulse and allows vacancies to be formed close to a di
amond surface without inducing surface graphitization. We operate in the previously unexplored regime where lattice vacancies are created following tunneling breakdown rather than multiphoton ionization. We present three samples in which NV-center arrays were laser-written at distances between ~1 $mu$m and 40 $mu$m from a diamond surface, all presenting narrow distributions of optical linewidths with means between 62.1 MHz and 74.5 MHz. The linewidths include the effect of long-term spectral diffusion induced by a 532 nm repump laser for charge-state stabilization, thereby emphasizing the particularly low charge-noise environment of the created color centers. Such high-quality NV centers are excellent candidates for practical applications employing two-photon quantum interference with separate NV centers. Finally, we propose a model for disentangling power broadening from inhomogeneous broadening in the NV center optical linewidth.
We report on two novel ways for patterning Lithium Niobate (LN) at submicronic scale by means of focused ion beam (FIB) bombardment. The first method consists of direct FIB milling on LiNbO3 and the second one is a combination of FIB milling on a dep
osited metallic layer and subsequent RIE (Reactive Ion Etching) etching. FIB images show in both cases homogeneous structures with well reproduced periodicity. These methods open the way to the fabrication of photonic crystals on LiNbO3 substrates.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
