اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدOn the interpretation of valence band photoemission spectra at organic-metal interfaces
134
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Adsorption of organic molecules on well-oriented single crystal coinage metal surfaces fundamentally affects the energy distribution curve of ultra-violet photoelectron spectroscopy spectra. New features not present in the spectrum of the pristine metal can be assigned as interface states having some degree of molecule-substrate hybridization. Here it is shown that interface states having molecular orbital character can easily be identified at low binding energy as isolated features above the featureless substrate sp-plateau. On the other hand much care must be taken in assigning adsorbate-induced features when these lie within the d-band spectral region of the substrate. In fact, features often interpreted as characteristic of the molecule-substrate interaction may actually arise from substrate photoelectrons scattered by the adsorbates. This phenomenon is illustrated through a series of examples of noble-metal single-crystal surfaces covered by monolayers of large pi-conjugated organic molecules.
قيم البحث
اقرأ أيضاً
The band alignment of semiconductor-metal interfaces plays a vital role in modern electronics, but remains difficult to predict theoretically and measure experimentally. For interfaces with strong band bending a main difficulty originates from the in
-built potentials which lead to broadened and shifted band spectra in spectroscopy measurements. In this work we present a method to resolve the band alignment of buried semiconductor-metal interfaces using core level photoemission spectroscopy and self-consistent electronic structure simulations. As a proof of principle we apply the method to a clean in-situ grown InAs(100)/Al interface, a system with a strong in-built band bending. Due to the high signal-to-noise ratio of the core level spectra the proposed methodology can be used on previously inaccessible semiconductor-metal interfaces and support targeted design of novel hybrid devices and form the foundation for a interface parameter database for specified synthesis processes of semiconductor-metal systems.
The interface formation between copper phthalocyanine (CuPc) and two representative metal substrates, i.e., Au and Co, was investigated by the combination of ultraviolet photoelectron spectroscopy and inverse photoelectron spectroscopy. The occupied
and unoccupied molecular orbitals and thus the transport band gap of CuPc are highly influenced by film thickness, i.e., molecule-substrate distance. Due to the image charge potential given by the metallic substrates the transport band gap of CuPc opens from $(1.4 pm 0.3)$ eV for 1 nm thickness to $(2.2 pm 0.3)$ eV, and saturates at this value above 10 nm CuPc thickness. The interface dipoles with values of 1.2 eV and 1.0 eV for Au and Co substrates, respectively, predominantly depend on the metal substrate work functions. X-ray photoelectron spectroscopy measurements using synchrotron radiation provide detailed information on the interaction between CuPc and the two metal substrates. While charge transfer from the Au or Co substrate to the Cu metal center is present only at sub-monolayer coverages, the authors observe a net charge transfer from the molecule to the Co substrate for films in the nm range. Consequently, the Fermi level is shifted as in the case of a p-type doping of the molecule. This is, however, a competing phenomenon to the energy band shifts due to the image charge potential.
The interaction of the strong electron-acceptor tetracyanoethylene (TCNE) with the Cu(100) surface has been studied with scanning tunneling microscopy experiments and first-principles density functional theory calculations. We compare two different a
dsorption models with the experimental results and show that the molecular self-assembly is caused by a strong structural modification of the Cu(100) surface rather than the formation of a coordination network by diffusing Cu adatoms. Surface atoms become highly buckled and the chemisorption of TCNE is accompanied by a partial charge-transfer.
Auger Photoelectron Coincidence Spectroscopy (APECS), in which the Auger spectra is measured in coincidence with the core level photoelectron, is capable of pulling difficult to observe low energy Auger peaks out of a large background due mostly to i
nelastically scattered valence band (VB) photoelectrons. However the APECS method alone cannot eliminate the background due to valence band photoemission processes in which the initial photon energy is shared by two or more electrons and one of the electrons is in the energy range of the core level photoemission peak. Here we describe an experimental method to determine the contributions from these background processes and apply this method in the case of Copper M3VV Auger spectrum obtained in coincidence with the 3p3/2 photoemission peak. A beam of 200 eV photons was incident on a Cu(100) sample and a series of coincidence measurements were performed using a spectrometer equipped with two cylindrical mirror analyzers (CMAs). One CMA was set at series of fixed energies that ranged between the energy of the core and the VB peaks. The other CMA was scanned over a range corresponding to electrons leaving the surface between 0eV and 70eV. The set of measured spectra were then fit to a parameterized function which was extrapolated to determine the background in the APECS spectra due to multi-electron and inelastic VB photoemission processes. The extrapolated background was subtracted from the APECS spectrum to obtain the spectrum of electrons emitted solely as the result of the Auger process. A comparison of the coincidence spectrum with the same spectrum with background removed shows that in the case of Cu M3VV the background due to the inelastic scattering of VB electrons is negligible in the region of the Auger peak but is more than half the total signal down in the low energy tail of the Auger peak.
We introduce a new method for determining accurate values of the valence-band maximum in x-ray photoemission spectra. Specifically, we align the sharpest peak in the valence-band region of the experimental spectrum with the corresponding feature of a
theoretical valence-band density of states curve from ab initio GW theory calculations. This method is particularly useful for soft and hard x-ray photoemission studies of materials with a mixture of valence-band characters, where strong matrix element effects can render standard methods for extracting the valence-band maximum unreliable. We apply our method to hydrogen-terminated boron-doped diamond, which is a promising substrate material for novel solar cell devices. By carrying out photoemission experiments with variable light polarizations, we verify the accuracy of our analysis and the general validity of the method.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
