اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدFabrication and characterization of vacuum deposited fluorescein thin films
438
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Simple vacuum evaporation technique for deposition of dyes on various solid surfaces has been developed. The method is compatible with conventional solvent-free nanofabrication processing enabling fabrication of nanoscale optoelectronic devices. Thin films of fluorescein were deposited on glass, fluorine-tin-oxide (FTO) coated glass with and without atomically layer deposited (ALD) nanocrystalline 20 nm thick anatase TiO2 coating. Surface topology, absorption and emission spectra of the films depends on their thickness and the material of supporting substrate. On a smooth glass surface the dye initially formes islands before merging into a uniform layer after 5 to 10 monolayers. On FTO covered glass the absorption spectra are similar to fluorescein solution in ethanol. Absorption spectra on ALD-TiO2 is red shifted compared to the film deposited on bare FTO. The corresponding emission spectra at {lambda} = 458 nm excitation show various thickness and substrate dependent features, while the emission of films deposited on TiO2 is quenched due to the effective electron transfer to the semiconductor conduction band.
قيم البحث
اقرأ أيضاً
Half-Heusler YPtSb thin films were fabricated by magnetron co-sputtering method on MgO-buffered SiO2/Si(001) substrates. X-ray diffraction pattern and Energy dispersive X-ray spectroscopy confirmed the high-quality growth and stoichiometry. The tempe
rature dependence of the resistivity shows a semiconducting-type behavior down to low temperature. The Hall mobility was determined to be 450 cm2/Vs at 300K, which is much higher than the bulk value (300 cm2/Vs). In-plane magnetoresistance (MR) measurements with fields applied along and perpendicular to the current direction show opposite MR signs, which suggests the possible existence of the topological surface states.
We report a detailed study of surface and interface properties of pulsed-laser deposited NiMnSb films on Si (100) substrate as a function of film thickness. As the thickness of films is reduced below 35 nm formation of a porous layer is observed. Por
osity in this layer increases with decrease in NiMnSb film thickness. These morphological changes of the ultra thin films are reflected in the interesting transport and magnetic properties of these films. On the other hand, there are no influences of compositional in-homogeneity and surface/interface roughness on the magnetic and transport properties of the films.
This paper reports the synthesis and detailed characterization of graphite thin films produced by thermal decomposition of the (0001) face of a 6H-SiC wafer, demonstrating the successful growth of single crystalline films down to approximately one gr
aphene layer. The growth and characterization were carried out in ultrahigh vacuum (UHV) conditions. The growth process and sample quality were monitored by low-energy electron diffraction, and the thickness of the sample was determined by core level x-ray photoelectron spectroscopy. High-resolution angle-resolved photoemission spectroscopy shows constant energy map patterns, which are very sharp and fully momentum-resolved, but nonetheless not resolution limited. We discuss the implications of this observation in connection with scanning electron microscopy data, as well as with previous studies.
The Fe-doped CuO thin films were deposited onto glass substrates by Spray pyrolysis technique. The structural, micro-structural, optical and electrical properties of the synthesized samples were investigated in details. The X-Ray diffraction (XRD), R
aman and Fourier Transform Infrared (FTIR) spectroscopy, confirmed that the studied samples exhibit single phase monoclinic structure of CuO. The UV-VIS spectrophotometer mentioned that the transmittance increases to 80 % when increasing the Fe concentration. Furthermore, the band gap energy of the obtained CuO was 1.29 eV. This value was slightly increased by the Fe substitution. In addition, the electrical properties of the films such as the conductivity, the mobility, the resistivity and the carrier concentration have been studied. The Hall Effect measurements confirmed the p-type conductivity of the studied films.
BaZrS3 is a prototypical chalcogenide perovskite, an emerging class of unconventional semiconductor. Recent results on powder samples reveal that it is a material with a direct band gap of 1.7-1.8 eV, a very strong light-matter interaction, and a hig
h chemical stability. However, many of the fundamental properties are unknown, hindering the ability to apply BaZrS3 for optoelectronics. Here we report the fabrication of BaZrS3 thin films, by sulfurization of oxide films deposited by pulsed laser deposition. We show that these films are n-type with carrier densities in the range of 10^19-10^20 cm^-3. Depending on the processing temperature, the Hall mobility ranges from 2.1 to 13.7 cm^2/Vs. The absorption coefficient is > 10^5 cm-1 at photon energy > 1.97 eV. Temperature dependent conductivity measurements suggest shallow donor levels. These results assure that BaZrS3 is a promising candidate for optoelectronics such as photodetectors, photovoltaics, and light emitting diodes.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
