اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThermally driven spin injection from a ferromagnet into a non-magnetic metal
159
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Creating, manipulating and detecting spin polarized carriers are the key elements of spin based electronics. Most practical devices use a perpendicular geometry in which the spin currents, describing the transport of spin angular momentum, are accompanied by charge currents. In recent years, new sources of pure spin currents, i.e., without charge currents, have been demonstrated and applied. In this paper, we demonstrate a conceptually new source of pure spin current driven by the flow of heat across a ferromagnetic/non-magnetic metal (FM/NM) interface. This spin current is generated because the Seebeck coefficient, which describes the generation of a voltage as a result of a temperature gradient, is spin dependent in a ferromagnet. For a detailed study of this new source of spins, it is measured in a non-local lateral geometry. We developed a 3D model that describes the heat, charge and spin transport in this geometry which allows us to quantify this process. We obtain a spin Seebeck coefficient for Permalloy of -3.8 microvolt/Kelvin demonstrating that thermally driven spin injection is a feasible alternative for electrical spin injection in, for example, spin transfer torque experiments.
قيم البحث
اقرأ أيضاً
We have calculated the spin-polarization effects of a current in a two dimensional electron gas which is contacted by two ferromagnetic metals. In the purely diffusive regime, the current may indeed be spin-polarized. However, for a typical device ge
ometry the degree of spin-polarization of the current is limited to less than 0.1%, only. The change in device resistance for parallel and antiparallel magnetization of the contacts is up to quadratically smaller, and will thus be difficult to detect.
We report electrical spin injection from a ferromagnetic metal contact into a semiconductor light emitting diode structure with an injection efficiency of 30% which persists to room temperature. The Schottky barrier formed at the Fe/AlGaAs interface
provides a natural tunnel barrier for injection of spin polarized electrons under reverse bias. These carriers radiatively recombine, emitting circularly polarized light, and the quantum selection rules relating the optical and carrier spin polarizations provide a quantitative, model-independent measure of injection efficiency. This demonstrates that spin injecting contacts can be formed using a widely employed contact methodology, providing a ready pathway for the integration of spin transport into semiconductor processing technology.
We present a theoretical analysis of current driven ferromagnetic resonance in a ferromagnet/normal-metal/ferromagnet tri-layer. This method of driving ferromagnetic resonance was recently realized experimentally by Tulapurkar et al. [Nature 438, 339
(2005)] and Sankey et al. [Phys. Rev. Lett. 96, 227601 (2006)]. The precessing magnetization rectifies the alternating current applied to drive the ferromagnetic resonance and leads to the generation of a dc voltage. Our analysis shows that a second mechanism to generate a dc voltage, rectification of spin currents emitted by the precessing magnetization, has a contribution to the dc voltage that is of approximately equal size for the thin ferromagnetic films used in the experiment.
A mesoscopic description of spin-transfer effect is proposed, based on the spin-injection mechanism occurring at the junction with a ferromagnet. The effect of spin-injection is to modify locally, in the ferromagnetic configuration space, the density
of magnetic moments. The corresponding gradient leads to a current-dependent diffusion process of the magnetization. In order to describe this effect, the dynamics of the magnetization of a ferromagnetic single domain is reconsidered in the framework of the thermokinetic theory of mesoscopic systems. Assuming an Onsager cross-coefficient that couples the currents, it is shown that spin-dependent electric transport leads to a correction of the Landau-Lifshitz-Gilbert equation of the ferromagnetic order parameter with supplementary diffusion terms. The consequence of spin-injection in terms of activation process of the ferromagnet is deduced, and the expressions of the effective energy barrier and of the critical current are derived. Magnetic fluctuations are calculated: the correction to the fluctuations is similar to that predicted for the activation. These predictions are consistent with the measurements of spin-transfer obtained in the activation regime and for ferromagnetic resonance under spin-injection.
In this paper, a 3-terminal spin-transfer torque nano-oscillator (STNO) is studied using the concurrent spin injection of a spin-polarized tunneling current and a spin Hall current exciting the free layer into dynamic regimes beyond what is achieved
by each individual mechanism. The pure spin injection is capable of inducing oscillations in the absence of charge currents effectively reducing the critical tunneling current to zero. This reduction of the critical charge currents can improve the endurance of both STNOs and non-volatile magnetic memories (MRAM) devices. It is shown that the system response can be described in terms of an injected spin current density $J_s$ which results from the contribution of both spin injection mechanisms, with the tunneling current polarization $p$ and the spin Hall angle $theta$ acting as key parameters determining the efficiency of each injection mechanism. The experimental data exhibits an excellent agreement with this model which can be used to quantitatively predict the critical points ($J_s = -2.26pm 0.09 times 10^9 hbar/e$ A/m$^2$) and the oscillation amplitude as a function of the input currents. In addition, the fitting of the data also allows an independent confirmation of the values estimated for the spin Hall angle and tunneling current polarization as well as the extraction of the damping $alpha = 0.01$ and non-linear damping $Q = 3.8pm 0.3$ parameters.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
