اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدComments on Effects of wall roughness on flow in nanochannels
124
0
0.0
(
0
)
تأليف
Zotin K.-H. Chu
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We make remarks on Sofos {it et al.}s [{it Phys. Rev. E} 79, 026305 (2009)] paper. The focus is about the monotonicity of the slip length of which it is different from previous similar numerical simulation. We also offer a possible explanation for this.
قيم البحث
اقرأ أيضاً
We make some remarks on Sokhan and Quirkes [{it Phys. Rev. E} 78, 015301(R) (2008)] paper (arXiv:0805.1666). Sokhan and Quirke mentioned that, considering their main result, {the slip coefficient is independent of the external force (flux)} which is
not consistent with previous measurements and approaches. We also discuss the sudden changes of the slip coefficient for larger Knudsen numbers or smaller nanopores.
The impact of wall roughness on fully developed laminar pipe flow is investigated numerically. The roughness is comprised of square bars of varying size and pitch. Results show that the inverse relation between the friction factor and the Reynolds nu
mber in smooth pipes still persists in rough pipes, regardless of the rib height and pitch. At a given Reynolds number, the friction factor varies quadratically with roughness height and linearly with roughness pitch. We propose a single correlation for the friction factor that successfully collapses the data.
In a series of papers, Bartelt and co-workers developed novel snow-avalanche models in which emph{random kinetic energy} $R_K$ (a.k.a. granular temperature) is a key concept. The earliest models were for a single, constant density layer, using a Voel
lmy model but with $R_K$-dependent friction parameters. This was then extended to variable density, and finally a suspension layer (powder-snow cloud) was added. The physical basis and mathematical formulation of these models is critically reviewed here, with the following main findings: (i) Key assumptions in the original RKE model differ substantially from established results on dense granular flows; in particular, the effective friction coefficient decreases to zero with velocity in the RKE model. (ii) In the variable-density model, non-canonical interpretation of the energy balance leads to a third-order evolution equation for the flow depth or density, whereas the stated assumptions imply a first-order equation. (iii) The model for the suspension layer neglects gravity and disregards well established theoretical and experimental results on particulate gravity currents. Some options for improving these aspects are discussed.
We experimentally study the influence of wall roughness on bubble drag reduction in turbulent Taylor-Couette flow, i.e. the flow between two concentric, independently rotating cylinders. We measure the drag in the system for the cases with and withou
t air, and add roughness by installing transverse ribs on either one or both of the cylinders. For the smooth wall case (no ribs) and the case of ribs on the inner cylinder only, we observe strong drag reduction up to $DR=33%$ and $DR=23%$, respectively, for a void fraction of $alpha=6%$. However, with ribs mounted on both cylinders or on the outer cylinder only, the drag reduction is weak, less than $DR=11%$, and thus quite close to the trivial effect of reduced effective density. Flow visualizations show that stable turbulent Taylor vortices --- large scale vortical structures --- are induced in these two cases, i.e. the cases with ribs on the outer cylinder. These strong secondary flows move the bubbles away from the boundary layer, making the bubbles less effective than what had previously been observed for the smooth-wall case. Measurements with counter-rotating smooth cylinders, a regime in which pronounced Taylor rolls are also induced, confirm that it is really the Taylor vortices that weaken the bubble drag reduction mechanism. Our findings show that, although bubble drag reduction can indeed be effective for smooth walls, its effect can be spoiled by e.g. biofouling and omnipresent wall roughness, as the roughness can induce strong secondary flows.
We report here on experiments and simulations examining the effect of changing wall friction on the gravity-driven flow of spherical particles in a vertical hopper. In 2D experiments and simulations, we observe that the exponent of the expected power
-law scaling of mass flow rate with opening size (known as Beverloos law) decreases as the coefficient of friction between particles and wall increases, whereas Beverloo scaling works as expected in 3D. In our 2D experiments, we find that wall friction plays the biggest role in a region near the outlet comparable in height to the largest opening size. However, wall friction is not the only factor determining a constant rate of flow, as we observe a near-constant mass outflow rate in the 2D simulations even when wall friction is set to zero. We show in our simulations that an increase in wall friction leaves packing fractions relatively unchanged, while average particle velocities become independent of opening size as the coefficient of friction increases. We track the spatial pattern of time-averaged particle velocities and accelerations inside the hopper. We observe that the hemisphere-like region above the opening where particles begin to accelerate is largely independent of opening size at finite wall friction. However, the magnitude of particle accelerations decreases significantly as wall friction increases, which in turn results in mean sphere velocities that no longer scale with opening size, consistent with our observations of mass flow rate scaling. The case of zero wall friction is anomalous, in that most of the acceleration takes place near the outlet.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
