اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدSimulation study of shock reaction on porous material
260
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Direct modeling of porous materials under shock is a complex issue. We investigate such a system via the newly developed material-point method. The effects of shock strength and porosity size are the main concerns. For the same porosity, the effects of mean-void-size are checked. It is found that, local turbulence mixing and volume dissipation are two important mechanisms for transformation of kinetic energy to heat. When the porosity is very small, the shocked portion may arrive at a dynamical steady state; the voids in the downstream portion reflect back rarefactive waves and result in slight oscillations of mean density and pressure; for the same value of porosity, a larger mean-void-size makes a higher mean temperature. When the porosity becomes large, hydrodynamic quantities vary with time during the whole shock-loading procedure: after the initial stage, the mean density and pressure decrease, but the temperature increases with a higher rate. The distributions of local density, pressure, temperature and particle-velocity are generally non-Gaussian and vary with time. The changing rates depend on the porosity value, mean-void-size and shock strength. The stronger the loaded shock, the stronger the porosity effects. This work provides a supplement to experiments for the very quick procedures and reveals more fundamental mechanisms in energy and momentum transportation.
قيم البحث
اقرأ أيضاً
Morphological measures are introduced to probe the complex procedure of shock wave reaction on porous material. They characterize the geometry and topology of the pixelized map of a state variable like the temperature. Relevance of them to thermodyna
mical properties of material is revealed and various experimental conditions are simulated. Numerical results indicate that, the shock wave reaction results in a complicated sequence of compressions and rarefactions in porous material. The increasing rate of the total fractional white area $A$ roughly gives the velocity $D$ of a compressive-wave-series. When a velocity $D$ is mentioned, the corresponding threshold contour-level of the state variable, like the temperature, should also be stated. When the threshold contour-level increases, $D$ becomes smaller. The area $A$ increases parabolically with time $t$ during the initial period. The $A(t)$ curve goes back to be linear in the following three cases: (i) when the porosity $delta$ approaches 1, (ii) when the initial shock becomes stronger, (iii) when the contour-level approaches the minimum value of the state variable. The area with high-temperature may continue to increase even after the early compressive-waves have arrived at the downstream free surface and some rarefactive-waves have come back into the target body. In the case of energetic material ... (see the full text)
The collapse of cavities under shock is a key problem in various fields ranging from erosion of material, ignition of explosive, to sonoluminescence, etc. We study such processes using the material-point-method developed recently in the field of soli
d physics. The main points of the research include the relations between symmetry of collapsing and the strength of shock, other coexisting interfaces, as well as hydrodynamic and thermal-dynamic behaviors ignored by the pure fluid models. In the case with strong shock, we study the procedure of jet creation in the cavity; in the case with weak shock, we found that the cavity can not be collapsed completely by the shock and the cavity may collapse in a nearly isotropic way. The history of collapsing significantly influences the distribution of hot spots in the shocked material. The change in symmetry of collapsing is investigated. Since we use the Mie-Gr% {u}neisen equation of state and the effects of strain rate are not taken into account, the behavior is the same if one magnifies the spatial and temporal scales in the same way.
Shock wave reaction results in various characteristic regimes in porous material. The geometrical and topological properties of these regimes are highly concerned in practical applications. Via the morphological analysis to characteristic regimes wit
h high temperature, we investigate the thermodynamics of shocked porous materials whose mechanical properties cover a wide range from hyperplasticity to elasticity. It is found that, under fixed shock strength, the total fractional area $A$ of the high-temperature regimes with $T geq T_{th}$ and its saturation value first increase, then decrease with the increasing of the initial yield $sigma_{Y0}$, where $T_{th}$ is a given threshold value of temperature $T$. In the shock-loading procedure, the fractional area $A(t)$ may show the same behavior if $T_{th}$ and $sigma_{Y0}$ are chosen appropriately. Under the same $A(t)$ behavior, $T_{th}$ first increases then decreases with $sigma_{Y0}$. At the maximum point $sigma_{Y0M}$, the shock wave contributes the maximum plastic work. Around $sigma_{Y0M}$, two materials with different mechanical properties may share the same $A(t)$ behavior even for the same $T_{th}$. The characteristic regimes in the material with the larger $sigma_{Y0}$ are more dispersed.
By means of ab initio calculations we investigate the possibility of existence of a boron nitride (BN) porous two-dimensional nanosheet which is geometrically similar to the carbon allotrope known as biphenylene carbon. The proposed structure, which
we called Inorganic Graphenylene (IGP), is formed spontaneously after selective dehydrogenation of the porous Boron Nitride (BN) structure proposed by Ding et al. We study the structural and electronic properties of both porous BN and IGP and it is shown that, by selective substitution of B and N atoms with carbon atoms in these structures, the band gap can be significantly reduced, changing their behavior from insulators to semiconductors, thus opening the possibility of band gap engineering for this class of two-dimensional materials.
The Hugoniot curves for shock-compressed molybdenum with initial porosities of 1.0, 1.26, 1.83, and 2.31 are theoretically investigated. The method of calculations combines the first-principles treatment for zero- and finite-temperature electronic co
ntribution and the mean-field-potential approach for the ion-thermal contribution to the total free energy. Our calculated results reproduce the Hugoniot properties of porous molybdenum quite well. At low porosity, in particular, the calculations show a complete agreement with the experimental measurements over the full range of data. For the two large porosity values of 1.83 and 2.31, our results are well in accord with the experimental data points up to the particle velocity of 3.5 km/s, and tend to overestimate the shock-wave velocity and Hugoniot pressure when further increasing the particle velocity. In addition, the temperature along the principal Hugoniot is also extensively investigated for porous molybdenum.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
