اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدTransient Analysis of Warm Electron Injection Programming of Double Gate SONOS Memories by means of Full Band Monte Carlo Simulation
128
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this paper we investigate Warm Electron Injection as a mechanism for NOR programming of double-gate SONOS memories through 2D full band Monte Carlo simulations. Warm electron injection is characterized by an applied VDS smaller than 3.15 V, so that electrons cannot easily accumulate a kinetic energy larger than the height of the Si/SiO2 barrier. We perform a time-dependent simulation of the program operation where the local gate current density is computed with a continuum-based method and is adiabatically separated from the 2D full Monte Carlo simulation used for obtaining the electron distribution in the phase space. In this way we are able to compute the time evolution of the charge stored in the nitride and of the threshold voltages corresponding to forward and reverse bias. We show that warm electron injection is a viable option for NOR programming in order to reduce power supply, preserve reliability and CMOS logic level compatibility. In addition, it provides a well localized charge, offering interesting perspectives for multi-level and dual bit operation, even in devices with negligible short channel effects.
قيم البحث
اقرأ أيضاً
In this paper we investigate warm electron injection in a double gate SONOS memory by means of 2D full-band Monte Carlo simulations of the Boltzmann Transport Equation (BTE). Electrons are accelerated in the channel by a drain-to-source voltage VDS s
maller than 3 V, so that programming occurs via electrons tunneling through a potential barrier whose height has been effectively reduced by the accumulated kinetic energy. Particle energy distribution at the semiconductor/oxide interface is studied for different bias conditions and different positions along the channel. The gate current is calculated with a continuum-based post-processing method as a function of the particle distribution obtained from Monte Carlo. Simulation results show that the gate current increases by several orders of magnitude with increasing drain bias and warm electron injection can be an interesting option for programming when short channel effects prohibit the application of larger drain bias.
Avalanche photodiodes fabricated from AlInAsSb grown as a digital alloy exhibit low excess noise. In this paper, we investigate the band structure-related mechanisms that influence impact ionization. Band-structures calculated using an empirical tigh
t-binding method and Monte Carlo simulations reveal that the mini-gaps in the conduction band do not inhibit electron impact ionization. Good agreement between the full band Monte Carlo simulations and measured noise characteristics is demonstrated.
The Boltzmann transport equation is one of the most relevant framework to study the heat transport at the nanoscale, beyond the diffusive regime and up to the micrometer-scale. In the general case of three-dimensional devices, the particle Monte Carl
o approach of phonon transport is particularly powerful and convenient, and requires reasonable computational resources. In this work, we propose an original and versatile particle Monte Carlo approach parametrized by using ab-initio data. Both the phonon dispersion and the phonon-phonon scattering rates have been computed by DFT calculation in the entire 3D Brillouin zone. To treat the phonon transport at rough interfaces, a combination of specular and diffuse reflections has been implemented in phase space. Thermal transport has been investigated in nanowires and thin films made of cubic and hexagonal Silicon, including edge roughness, in terms of effective thermal conductivity, phonon band contributions and heat flux orientation. It is shown that the effective thermal conductivity in quasi-ballistic regime obtained from our Monte Carlo simulation cannot be accurately fitted by simple semi-analytical Matthiessen-like models and that spectral approaches are mandatory to get good results. Our Full Band approach shows that some phonon branches exhibiting a negative group velocity in some parts of the Brillouin zone may contribute negatively to the total thermal flux. Besides, the thermal flux clearly appears to be oriented along directions of high density of states. The resulting anisotropy of the heat flux is discussed together with the influence of rough interfaces.
Designing platforms to control phase-coherence and interference of electron waves is a cornerstone for future quantum electronics, computing or sensing. Nanoporous graphene (NPG) consisting of linked graphene nanoribbons has recently been fabricated
using molecular precursors and bottom-up assembly [Moreno et al., Science 360, 199 (2018)] opening an avenue for controlling the electronic current in a two-dimensional material. By simulating electron transport in real-sized NPG samples we predict that electron waves injected from the tip of a scanning tunneling microscope (STM) behave similarly to photons in coupled waveguides, displaying a Talbot interference pattern. We link the origins of this effect to the band structure of the NPG and further demonstrate how this pattern may be mapped out by a second STM probe. We enable atomistic parameter-free calculations beyond the 100 nm scale by developing a new multi-scale method where first-principles density functional theory regions are seamlessly embedded into a large-scale tight-binding.
An intrinsic electron injection model for linear band two-dimensional (2D) materials, like graphene, is presented and its coupling to a recently developed quantum time-dependent Monte Carlo simulator for electron devices, based on the use of stochast
ic Bohmian conditional wave functions, is explained. The simulator is able to capture the full (DC, AC, transient and noise) performance of 2D electron devices. In particular, we demonstrate that the injection of electrons with positive and negative kinetic energies is mandatory when investigating high frequency performance of linear band materials with Klein tunneling, while traditional models dealing with holes (defined as the lack of electrons) can lead to unphysical results. We show that the number of injected electrons is bias-dependent, implying that an extra charge is required to get self-consistent results. Interestingly, we provide a successful comparison with experimental DC data. Finally, we predict that a genuine high-frequency signature due to a roughly constant electron injection rate in 2D linear band electron devices (which is missing in 2D parabolic band ones) can be used as a band structure tester.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
