Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userEfficient Simulations of Propagating Flames Using Adaptive Mesh Refinement
67
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Wildland fires are complex multi-physics problems that span wide spatial scale ranges. Capturing this complexity in computationally affordable numerical simulations for process studies and outer-loop techniques (e.g., optimization and uncertainty quantification) is a fundamental challenge in reacting flow research. Further complications arise for propagating fires where a priori knowledge of the fire spread rate and direction is typically not available. In such cases, static mesh refinement at all possible fire locations is a computationally inefficient approach to bridging the wide range of spatial scales relevant to wildland fire behavior. In the present study, we address this challenge by incorporating adaptive mesh refinement (AMR) in fireFoam, an OpenFOAM solver for simulations of complex fire phenomena. The AMR functionality in the extended solver, called wildFireFoam, allows us to dynamically track regions of interest and to avoid inefficient over-resolution of areas far from a propagating flame. We demonstrate the AMR capability for fire spread on vertical panels and for large-scale fire propagation on a variable-slope surface that is representative of real topography. We show that the AMR solver reproduces results obtained using much larger statically refined meshes, at a substantially reduced computational cost.
rate research
Read More
The physical characteristics and evolution of a large-scale helium plume are examined through a series of numerical simulations with increasing physical resolution using adaptive mesh refinement (AMR). The five simulations each model a 1~m diameter circular helium plume exiting into a (4~m)$^3$ domain, and differ solely with respect to the smallest scales resolved using the AMR, spanning resolutions from 15.6~mm down to 0.976~mm. As the physical resolution becomes finer, the helium-air shear layer and subsequent Kelvin-Helmholtz instability are better resolved, leading to a shift in the observed plume structure and dynamics. In particular, a critical resolution is found between 3.91~mm and 1.95~mm, below which the mean statistics and frequency content of the plume are altered by the development of a Rayleigh-Taylor instability near the centerline in close proximity to the base of the plume. This shift corresponds to a plume puffing frequency that is slightly higher than would be predicted using empirical relationships developed for buoyant jets. Ultimately, the high-fidelity simulations performed here are intended as a new validation dataset for the development of subgrid-scale models used in large eddy simulations of real-world buoyancy-driven flows.
We study dendritic microstructure evolution using an adaptive grid, finite element method applied to a phase-field model. The computational complexity of our algorithm, per unit time, scales linearly with system size, rather than the quadratic variation given by standard uniform mesh schemes. Time-dependent calculations in two dimensions are in good agreement with the predictions of solvability theory, and can be extended to three dimensions and small undercoolings
We have explored the evolution of gas distributions from cosmological simulations carried out using the RAMSES adaptive mesh refinement (AMR) code, to explore the effects of resolution on cosmological hydrodynamical simulations. It is vital to understand the effect of both the resolution of initial conditions and the final resolution of the simulation. Lower initial resolution simulations tend to produce smaller numbers of low mass structures. This will strongly affect the assembly history of objects, and has the same effect of simulating different cosmologies. The resolution of initial conditions is an important factor in simulations, even with a fixed maximum spatial resolution. The power spectrum of gas in simulations using AMR diverges strongly from the fixed grid approach - with more power on small scales in the AMR simulations - even at fixed physical resolution and also produces offsets in the star formation at specific epochs. This is because before certain times the upper grid levels are held back to maintain approximately fixed physical resolution, and to mimic the natural evolution of dark matter only simulations. Although the impact of hold back falls with increasing spatial and initial-condition resolutions, the offsets in the star formation remain down to a spatial resolution of 1 kpc. These offsets are of order of 10-20%, which is below the uncertainty in the implemented physics but are expected to affect the detailed properties of galaxies. We have implemented a new grid-hold-back approach to minimize the impact of hold back on the star formation rate.
To date, fully cosmological hydrodynamic disk simulations to redshift zero have only been undertaken with particle-based codes, such as GADGET, Gasoline, or GCD+. In light of the (supposed) limitations of traditional implementations of smoothed particle hydrodynamics (SPH), or at the very least, their respective idiosyncrasies, it is important to explore complementary approaches to the SPH paradigm to galaxy formation. We present the first high-resolution cosmological disk simulations to redshift zero using an adaptive mesh refinement (AMR)-based hydrodynamical code, in this case, RAMSES. We analyse the temporal and spatial evolution of the simulated stellar disks vertical heating, velocity ellipsoids, stellar populations, vertical and radial abundance gradients (gas and stars), assembly/infall histories, warps/lopsideness, disk edges/truncations (gas and stars), ISM physics implementations, and compare and contrast these properties with our sample of cosmological SPH disks, generated with GCD+. These preliminary results are the first in our long-term Galactic Archaeology Simulation program.
A numerical code for solving various Lyman alpha (Lya) radiative transfer (RT) problems is presented. The code is suitable for an arbitrary, three-dimensional distribution of Lya emissivity, gas temperature, density, and velocity field. Capable of handling Lya RT in an adaptively refined grid-based structure, it enables detailed investigation of the effects of clumpiness of the interstellar (or intergalactic) medium. The code is tested against various geometrically and physically idealized configurations for which analytical solutions exist, and subsequently applied to three Lyman-break galaxies, extracted from high-resolution cosmological simulations at redshift z = 3.6. Proper treatment of the Lya scattering reveals a diversity of surface brightness (SB) and line profiles. Specifically, for a given galaxy the maximum observed SB can vary by an order of magnitude, and the total flux by a factor of 3 - 6, depending on the viewing angle. This may provide an explanation for differences in observed properties of high-redshift galaxies, and in particular a possible physical link between Lyman-break galaxies and regular Lya emitters.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
