Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userModeling of Electro-deposition and Mechanical Stability at Li Metal/Solid Electrolyte Interface during Plating in Solid-State Batteries
84
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Interfacial deposition stability between Li metal and a solid electrolyte (SE) is important in preventing interfacial contact loss, mechanical fracture, and dendrite growth in Li-metal solid-state batteries (SSB). In this work, we investigate the deposition and mechanical stability at the Li metal/SE interface and its consequences (such as SE fracture and contact loss). A wide range of contributing factors are investigated, such as charge and mass transfer kinetics, the plasticity of Li metal and fracture of the SE, and the applied stack pressure. We quantify the effect of the ionic conductivity of the SE, the exchange current density of the interfacial charge-transfer reaction and SE surface roughness on the Li deposition stability at the Li metal/SE interface. We also propose a mechanical stability window for the applied stack pressure that can prevent both contact loss and SE fracture, which can be extended to other metal-electrode (such as Sodium) SSB systems.
rate research
Read More
Using a new class of (BH4)- substituted argyrodite Li6PS5Z0.83(BH4)0.17, (Z = Cl, I) solid electrolyte, Li-metal solid-state batteries operating at room temperature have been developed. The cells were made by combining the modified argyrodite with an In-Li anode and two types of cathode: an oxide, LixMO2 (M = 1/3Ni, 1/3Mn, 1/3Co; so called NMC) and a titanium disulfide, TiS2. The performance of the cells was evaluated through galvanostatic cycling and Alternating Current AC electrochemical impedance measurements. Reversible capacities were observed for both cathodes for at least tens of cycles. However, the high-voltage oxide cathode cell shows lower reversible capacity and larger fading upon cycling than the sulfide one. The AC impedance measurements revealed an increasing interfacial resistance at the cathode side for the oxide cathode inducing the capacity fading. This resistance was attributed to the intrinsic poor conductivity of NMC and interfacial reactions between the oxide material and the argyrodite electrolyte. On the contrary, the low interfacial resistance of the TiS2 cell during cycling evidences a better chemical compatibility between this active material and substituted argyrodites, allowing full cycling of the cathode material, 240 mAhg-1, for at least 35 cycles with a coulombic efficiency above 97%.
Several active areas of research in novel energy storage technologies, including three-dimensional solid state batteries and passivation coatings for reactive battery electrode components, require conformal solid state electrolytes. We describe an atomic layer deposition (ALD) process for a member of the lithium phosphorus oxynitride (LiPON) family, which is employed as a thin film lithium-conducting solid electrolyte. The reaction between lithium tert-butoxide (LiO$^t$Bu) and diethyl phosphoramidate (DEPA) produces conformal, ionically conductive thin films with a stoichiometry close to Li$_2$PO$_2$N between 250 and 300$^circ$C. The P/N ratio of the films is always 1, indicative of a particular polymorph of LiPON which closely resembles a polyphosphazene. Films grown at 300$^circ$C have an ionic conductivity of $6.51:(pm0.36)times10^{-7}$ S/cm at 35$^circ$C, and are functionally electrochemically stable in the window from 0 to 5.3V vs. Li/Li$^+$. We demonstrate the viability of the ALD-grown electrolyte by integrating it into full solid state batteries, including thin film devices using LiCoO$_2$ as the cathode and Si as the anode operating at up to 1 mA/cm$^2$. The high quality of the ALD growth process allows pinhole-free deposition even on rough crystalline surfaces, and we demonstrate the fabrication and operation of thin film batteries with the thinnest (<100nm) solid state electrolytes yet reported. Finally, we show an additional application of the moderate-temperature ALD process by demonstrating a flexible solid state battery fabricated on a polymer substrate.
The penetration of dendrites in ceramic lithium conductors severely constrains the development of solid-state batteries (SSBs) while its nanoscopic origin remain unelucidated. We develop an in-situ nanoscale electrochemical characterization technique to reveal the nanoscopic lithium dendrite growth kinetics and use it as a guiding tool to unlock the design of interfaces for dendrite-proof SSBs. Using Li7La3Zr2O12 (LLZO) as a model system, in-situ nanoscopic dendrite triggering measurements, ex-situ electro-mechanical characterizations, and finite element simulations are carried out which reveal the dominating role of Li+ flux detouring and nano-mechanical inhomogeneity on dendrite penetration. To mitigate such nano-inhomogeneity, an ionic-conductive homogenizing layer based on poly(propylene carbonate) is designed which in-situ reacts with lithium to form a highly conformal interphase at mild conditions. A high critical current density of 1.8mA cm-2 and a low interfacial resistance of 14{Omega} cm2 is achieved. Practical SSBs based on LiFePO4 cathodes show great cyclic stability without capacity decay over 300 cycles. Beyond this, highly reversible electrochemical dendrite healing behavior in LLZO is discovered using the nano-electrode, based on which a model memristor with a high on/off ratio of ~10^5 is demonstrated for >200 cycles. This work not only provides a novel tool to investigate and design interfaces in SSBs but offers also new opportunities for solid electrolytes beyond energy applications.
The existence of passivating layers at the interfaces is a major factor enabling modern lithium-ion (Li-ion) batteries. Their properties determine the cycle life, performance, and safety of batteries. A special case is the solid electrolyte interphase (SEI), a heterogeneous multi-component film formed due to the instability and subsequent decomposition of the electrolyte at the surface of the anode. The SEI acts as a passivating layer that hinders further electrolyte disintegration, which is detrimental to the Coulombic efficiency. In this work, we use first-principles simulations to investigate the kinetic and electronic properties of the interface between lithium fluoride (LiF) and lithium carbonate (Li$_2$CO$_3$), two common SEI components present in Li-ion batteries with organic liquid electrolytes. We find a coherent interface between these components that restricts the strain in each of them to below 3%. We find that the interface causes a large increase in the formation energy of the Frenkel defect, generating Li vacancies in LiF and Li interstitials in Li$_2$CO$_3$ responsible for transport. On the other hand, the Li interstitial hopping barrier is reduced from $0.3$ eV in bulk Li$_2$CO$_3$ to $0.10$ or $0.22$ eV in the interfacial structure considered, demonstrating the favorable role of the interface. Controlling these two effects in a heterogeneous SEI is crucial for maintaining fast ion transport in the SEI. We further perform Car-Parrinello molecular dynamics simulations to explore Li ion conduction in our interfacial structure, which reveal an enhanced Li ion diffusion in the vicinity of the interface. Understanding the interfacial properties of the multiphase SEI represents an important frontier to enable next-generation batteries.
Solid state electrolytes are widely considered as the enabler of lithium metal anodes for safe, durable and high energy density rechargeable lithium ion batteries. Despite the promise, failure mechanisms associated with solid state batteries are not well-established, largely due to limited understanding of the chemomechanical factors governing them. We focus on the recent developments in understanding the solid state aspects including the effects of mechanical stresses, constitutive relations, fracture, void formation and outline the gaps in literature. We also provide an overview of the manufacturing and processing of solid state batteries in relation to chemomechanics. The gaps identified provides concrete directions towards the rational design and development of failure resistant solid state batteries.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
