Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userCurvature as a guiding field for patterns in thin block copolymer films
61
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Experimental data on thin films of cylinder-forming block copolymers (BC) -- free-standing BC membranes as well as supported BC films -- strongly suggest that the local orientation of the BC patterns is coupled to the geometry in which the patterns are embedded. We analyze this phenomenon using general symmetry considerations and numerical self-consistent field studies of curved BC films in cylindrical geometry. The stability of the films against curvature-induced dewetting is also analyzed. In good agreement with experiments, we find that the BC cylinders tend to align along the direction of curvature at high curvatures. At low curvatures, we identify a transition from perpendicular to parallel alignment in supported films, which is absent in free standing membranes. Hence both experiments and theory show that curvature can be used to manipulate and align BC patterns.
rate research
Read More
An extensive study of single block copolymer knots containing two kinds of monomers $A$ and $B$ is presented. The knots are in a solution and their monomers are subjected to short range interactions that can be attractive or repulsive. In view of possible applications in medicine and the construction of intelligent materials, it is shown that several features of copolymer knots can be tuned by changing the monomer configuration. A very fast and abrupt swelling with increasing temperature is obtained in certain multiblock copolymers, while the size and the swelling behavior at high temperatures may be controlled in diblock copolymers. Interesting new effects appear in the thermal diagrams of copolymer knots when their length is increased.
Thin block copolymer films have attracted considerable academic attention because of their ability to self-assemble into various microstructures, many of which have potential technological applications. Despite the ongoing interest, little effort has focused on the onset of plasticity and failure which are important factors for the eventual adoption of these materials. Here we use delamination to impart a quantifiable local stain on thin films of homopolymer polystyrene and poly(2-vinylpyridine), as well as block copolymers made of styrene and 2-vinylpyridine. Direct observation of the damage caused by bending with atomic force microscopy and laser scanning confocal microscopy, leads to the identification of a critical strain for the onset of plasticity. Moving beyond our initial scaling analysis, the more quantitative analysis presented here shows strain levels for thick films to be comparable to bulk measurements. Monitoring the critical strain leads to several observations: 1.) as-cast PS-P2VP has low critical strain, 2.) annealing slowly increases critical strain as microstructural ordering takes place, and 3.) similar to the homopolymer, both as cast and ordered films both show increasing critical strain under confinement.
Simulations of five different coarse-grained models of symmetric diblock copolymer melts are compared to demonstrate a universal (i.e., model-independent) dependence of the free energy on the invariant degree of polymerization $overline{N}$, and to study universal properties of the order-disorder transition (ODT). The ODT appears to exhibit two regimes: Systems of very long chains ($overline{N} gtrsim 10^{4}$) are well described by the Fredrickson-Helfand theory, which assumes weak segregation near the ODT. Systems of smaller but experimentally relevant values, $overline{N} lesssim 10^4$, undergo a transition between strongly segregated disordered and lamellar phases that, though universal, is not adequately described by any existing theory.
Poly(ethylene oxide)-$textit{b}$-poly(butylmethacrylate) (PEO-$textit{b}$-PBMA) copolymers have recently been identified as excellent building blocks for the synthesis of hierarchical nanoporous materials. Nevertheless, while experiments have unveiled their potential to form bicontinuous phases and vesicles, a general picture of their phase and aggregation behavior is still missing. By performing Molecular Dynamics simulations, we here apply our recent coarse-grained model of PEO-$textit{b}$-PBMA to investigate its self-assembly in water and tetrahydrofuran (THF) and unveil the occurrence of a wide spectrum of mesophases. In particular, we find that the morphological phase diagram of this ternary system incorporates bicontinuous and lamellar phases at high copolymer concentrations, and finite-size aggregates, such as dispersed sheets or disk-like aggregates, spherical vesicles and rod-like vesicles, at low copolymer concentrations. The morphology of these mesophases can be controlled by tuning the THF/water relative content, which has a striking effect on the kinetics of self-assembly as well as on the resulting equilibrium structures. Our results disclose the fascinating potential of PEO-$textit{b}$-PBMA copolymers for the templated synthesis of nanostructured materials and offer a guideline to fine-tune their properties by accurately selecting the THF/water ratio.
We elucidate the roles of the isotropic-nematic (I-N) and nematic-smectic A (N-SmA) transitions in magnetic field directed self-assembly of a liquid crystalline block copolymer (BCP), using textit{in situ} x-ray scattering. Cooling into the nematic from the disordered melt yields poorly ordered and weakly aligned BCP microdomains. Continued cooling into the SmA however results in an abrupt increase in BCP orientational order with microdomain alignment tightly coupled to the translational order parameter of the smectic layers. These results underscore the significance of the N-SmA transition in generating highly aligned states under magnetic fields in these hierarchically ordered materials.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
