Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userFinite element analysis of fretting crack propagation
99
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
In this work, the finite elements method (FEM) is used to analyse the growth of fretting cracks. FEM can be favourably used to extract the stress intensity factors in mixed mode, a typical situation for cracks growing in the vicinity of a fretting contact. The present study is limited to straight cracks which is a simple system chosen to develop and validate the FEM analysis. The FEM model is tested and validated against popular weight functions for straight cracks perpendicular to the surface. The model is then used to study fretting crack growth and understand the effect of key parameters such as the crack angle and the friction between crack faces. Predictions achieved by this analysis match the essential features of former experimental fretting results, in particular the average crack arrest length can be predicted accurately.
rate research
Read More
This paper presents an experimental study of the fretting crack nucleation threshold, expressed in terms of loading conditions, with a cylinder/plane contact. The studied material is a damage tolerant aluminium alloy widely used in the aerospace application. Since in industrial problems, the surface quality is often variable, the impact of a unidirectional roughness is investigated via varying the roughness of the counter body in the fretting experiments. As expected, experimental results show a large effect of the contact roughness on the crack nucleation conditions. Rationalisation of the crack nucleation boundary independently of the studied roughnesses was successfully obtained by introducing the concept of effective contact area. This does show that the fretting crack nucleation of the studied material can be efficiently described by the local effective loadings inside the contact. Analytical prediction of the crack nucleation is presented with the Smith-Watson-Topper (SWT) parameter and size effect is also studied and discussed.
In regions where ice sheets are increasing in mass, there is a 50-200 m layer of old snow called firn which does not melt in the summer months. The density of firn tracks the transformation of snow into glacial ice at approximately 917 kg m^-3. The process of firn densification is important in at least two ways: 1) it can be a dominant component in the observed rate of change of the surface elevation, and 2) storage of liquid water in the lower density firn layer is now considered a critical component in the mass balance of ice sheets. If the rate of change of surface elevation can be equated with the rate of change in the mass of the ice sheet, we would have an excellent means of monitoring ice sheet mass balance. However, knowledge of firn densification rates is needed to make the inference of mass rate of change from volume rate of change. Several firn models have been created for areas without melt. We have reformulated these models with the finite-element software package FEniCS and integrated them with an enthalpy-formulation. This integration allows us to account for the melting and subsequent re-freezing of firn layers into ice lenses.
A compartment fire (a fire in a room or building) creates temperature gradients and inhomogeneous time-varying temperature, density, and flow fields. This work compared experimental measurements of the room acoustic impulse/frequency response in a room with a fire to numerically modeled responses. The fire is modeled using Fire Dynamics Simulator (FDS). Acoustic modeling was performed using the temperature field computed by FDS. COMSOL Multiphysics was used for finite element acoustic modeling and Bellhop for ray-trace acoustics modeling. The results show that the fire causes wave-fronts to arrive earlier (due to the higher sound speed) and with more variation in the delay times (due to the sound speed perturbations). The frequency response shows that the modes are shifted up in frequency and high frequency (>2500 Hz) modes are significantly attenuated. Model results are compared with data and show good agreement in observed trends.
We show that for the simulation of crack propagation in quasi-brittle, two-dimensional solids, very good results can be obtained with an embedded strong discontinuity quadrilateral finite element that has incompatible modes. Even more importantly, we demonstrate that these results can be obtained without using a crack tracking algorithm. Therefore, the simulation of crack patterns with several cracks, including branching, becomes possible. The avoidance of a tracking algorithm is mainly enabled by the application of a novel, local (Gauss-point based) criterion for crack nucleation, which determines the time of embedding the localisation line as well as its position and orientation. We treat the crack evolution in terms of a thermodynamical framework, with softening variables describing internal dissipative mechanisms of material degradation. As presented by numerical examples, many elements in the mesh may develop a crack, but only some of them actually open and/or slide, dissipate fracture energy, and eventually form the crack pattern. The novel approach has been implemented for statics and dynamics, and the results of computed difficult examples (including Kalthoffs test) illustrate its very satisfying performance. It effectively overcomes unfavourable restrictions of the standard embedded strong discontinuity formulations, namely the simulation of the propagation of a single crack only. Moreover, it is computationally fast and straightforward to implement. Our numerical solutions match the results of experimental tests and previously reported numerical results in terms of crack pattern, dissipated fracture energy, and load-displacement curve.
Photoacoustic imaging is an emerging technology based on the photoacoustic effect that has developed rapidly in recent years. It combines the high contrast of optical imaging and the high penetration and high resolution of acoustic imaging. As a non-destructive biological tissue imaging technology, photoacoustic imaging has important application value in the field of biomedicine. With its high efficiency bi-oimaging capabilities and excellent biosafety performance, it has been favored by researchers. The visualization of photoacoustic imaging has great research signifi-cance in the early diagnosis of some diseases, especially tumors. In photoacoustic imaging, light transmission and thermal effects are important processes. This article is based on COMSOL software and uses finite element analysis to construct a physi-cal model for simulation. Through laser pulses into the stomach tissue containing tumor, the physical process of light transmission and biological heat transfer was studied, and a photothermal model composed of two physical fields was built, and finally a series of visualization graphics were obtained. This work has certain theo-retical guiding significance for further promoting the application of photoacoustic imaging in the field of biomedicine.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
