Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userA Polarized Electron RF Photoinjector Using the Plane-Wave-Transformer (PWT) Design
92
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Polarized electron beams are now in routine use in particle accelerators for nuclear and high energy physics experiments. These beams are presently produced by dc-biased photoelectron sources combined with rf chopping and bunching systems with inherently high transverse emittances. Low emittances can be produced with an rf gun, but the vacuum environment has until now been considered too harsh to support a negative electron affinity GaAs photocathode. We propose to significantly improve the vacuum conditions by adapting a PWT rf photoinjector to achieve reasonable cathode emission rates and lifetimes. This adaptation can also be combined with special optics that will result in a flat beam with a normalized rms emittance in the narrow dimension that may be as low as 10-8 m.
rate research
Read More
Future colliders that require low-emittance highly-polarized electron beams are the main motivation for developing a polarized rf gun. However there are both technical and physics issues in generating highly polarized electron beams using rf guns that remain to be resolved. The PWT design offers promising features that may facilitate solutions to technical problems such as field emission and poor vacuum. Physics issues such as emission time now seem to be satisfactorily resolved. Other issues, such as the effect of magnetic fields at the cathode-both those associated with the rf field and those imposed by schemes to produce flat beams-are still open questions. Potential solution of remaining problems will be discussed in the context of the PWT design.
We report the results of a recent beam dynamics study, motivated by the need to redesign the LCLS photoinjector, that lead to the discovery of a new effective working point for a split RF photoinjector. We consider the emittance compensation regime of a space charge beam: by increasing the solenoid strength, the emittance evolution shows a double minimum behavior in the drifting region. If the booster is located where the relative emittance maximum and the envelope waist occur, the second emittance minimum can be shifted to the booster exit and frozen at a very low level (0.3 mm-mrad for a 1 nC flat top bunch), to the extent that the invariant envelope matching conditions are satisfied. Standing Wave Structures or alternatively Traveling Wave Structures embedded in a Long Solenoid are both candidates as booster linac. A careful measurement of the emittance evolution as a function of position in the drifting region is necessary to verify the computation and to determine experimentally the proper position of the booster cavities. The new design study and supporting experimental program under way at the SLAC Gun Test Facility are discussed.
Proposed fourth generation light sources using SASE FELs to generate short pulse, coherent, X-rays require demonstration of high brightness electron sources. The Gun Test Facility (GTF) at SLAC was built to test high brightness sources for the proposed Linac Coherent Light Source at SLAC. The transverse emittance measurements are made at nearly 30 MeV by measuring the spot size on a YAG screen using the quadrupole scan technique. The emittance was measured to vary from 1 to 3.5 mm-mrad as the charge is increased from 50 to 350 pC using a laser pulse width of 2 ps FWHM. The measurements are in good agreement with simulation results using the LANL version of PARMELA.
The design of the Linac Coherent Light Source assumes that a low-emittance, 1-nC, 10-ps beam will be available for injection into the 15-GeV linac. The proposed rf photocathode injector that will provide a 150-MeV beam with rms normalized emittances of 1 mm in both the transverse and longitudinal dimensions is based on a 1.6-cell S-band rf gun that is equipped with an emittance compensating solenoid. The booster accelerator is positioned at the beam waist coinciding with the first emittance maximum and is provided with an accelerating gradient of ~25 MeV/m, i.e., the new working point. The uv pulses required for cathode excitation will be generated by tripling the output of a Ti:sapphire laser system consisting of a highly stable cw mode-locked oscillator and two bow-tie amplifiers pumped by a pair of Q-switched Nd:YAG lasers. The large bandwidth of the Ti:sapphire system accommodates the desired temporal pulse shaping. Details of the design and the supporting simulations are presented.
Thermal emittance and quantum efficiency (QE) are key figures of merit of photocathodes, and their uniformity is critical to high-performance photoinjectors. Several QE mapping technologies have been successfully developed; however, there is still a dearth of information on thermal emittance maps. This is because of the extremely time-consuming procedure to gather measurements by scanning a small beam across the cathode with fine steps. To simplify the mapping procedure, and to reduce the time required to take measurements, we propose a new method that requires only a single scan of the solenoid current to simultaneously obtain thermal emittance and QE distribution by using a pattern beam with multiple beamlets. In this paper, its feasibility has been confirmed by both beam dynamics simulation and theoretical analysis. The method has been successfully demonstrated in a proof-of-principle experiment using an L-band radiofrequency photoinjector with a cesium telluride cathode. In the experiment, seven beamlets were generated from a microlens array system and their corresponding thermal emittance and QE varied from 0.93 to 1.14 $mu$m/mm and from 4.6 to 8.7%, respectively. We also discuss the limitations and future improvements of the method in this paper.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
