Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userForce Detection Sensitivity Spectrum Calibration of Levitated Nanomechanical Sensor Using Harmonic Coulomb Force
124
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Oscillators based on levitated particles are promising for the development of ultrasensitive force detectors. The theoretical performance of levitated nanomechanical sensors is usually characterized by the so-called thermal noise limit force detection sensitivity, which does not exhibit spectral specificity in practical measurements. To characterize the actual detection performance, we propose a method for the force detection sensitivity calibration of a levitated nanomechanical sensor based on the harmonic Coulomb force. Utilizing the measured transfer function, we obtained the force detection sensitivity spectrum from the position spectrum. Although the thermal noise limit force detection sensitivity of the system reached $rmleft( {4.39 pm 0.62} right) times {10^{ - 20}} N/H{z^{1/2}}$ at $rm{2.4times10^{-6} mbar}$ with feedback cooling, the measured sensitivity away from the resonance was of the order of $rm10^{-17} N/Hz^{1/2}$ based on the existing detection noise level. The calibration method established in our study is applicable to the performance evaluation of any optical levitation system for high-sensitivity force measurements.
rate research
Read More
Nanomechanical resonators are widely operated as force and mass sensors with sensitivities in the zepto-Newton and yocto-gram regime, respectively. Their accuracy, however, is usually undermined by high uncertainties in the effective mass of the system, whose estimation is a non-trivial task. This critical issue can be addressed in levitodynamics, where the nanoresonator typically consists of a single silica nanoparticle of well-defined mass. Yet, current methods assess the mass of the levitated nanoparticles with uncertainties up to a few tens of percent, therefore preventing to achieve unprecedented sensing performances. Here, we present a novel measurement protocol that uses the electrical field from a surrounding plate capacitor to directly drive a charged optically levitated particle in moderate vacuum. The developed technique estimates the mass within a statistical error below 1% and a systematic error of 2%, and paves the way toward more reliable sensing and metrology applications of levitodynamics systems.
Axion-like particles (ALPs) are predicted to mediate exotic interactions between spin and mass. We propose an ALP-searching experiment based on the levitated micromechanical oscillator, which is one of the most sensitive sensors for spin-mass forces at a short distance. The proposed experiment tests the spin-mass resonant interaction between the polarized electron spins and a diamagnetically levitated microsphere. By periodically flipping the electron spins, the contamination from nonresonant background forces can be eliminated. The levitated microoscillator can prospectively enhance the sensitivity by nearly $10^3$ times over current experiments for ALPs with mass in the range 4 meV to 0.4 eV.
An ultra-sensitive opto-mechanical force sensor has been built and tested in the optics laboratory at INFN Trieste. Its application to experiments in the Dark Energy sector, such as those for Chameleon-type WISPs, is particularly attractive, as it enables a search for their direct coupling to matter. We present here the main characteristics and the absolute force calibration of the KWISP (Kinetic WISP detection) sensor. It is based on a thin Si3N4 micro-membrane placed inside a Fabry-Perot optical cavity. By monitoring the cavity characteristic frequencies it is possible to detect the tiny membrane displacements caused by an applied force. Far from the mechanical resonant frequency of the membrane, the measured force sensitivity is 5.0e-14 N/sqrt(Hz), corresponding to a displacement sensitivity of 2.5e-15 m/sqrt(Hz), while near resonance the sensitivity is 1.5e-14 N/sqrt(Hz), reaching the estimated thermal limit, or, in terms of displacement, 7.5e-16 N/sqrt(Hz). These displacement sensitivities are comparable to those that can be achieved by large interferometric gravitational wave detectors.
Interferometric position detection of levitated particles is crucial for the centre-of-mass (CM) motion cooling and manipulation of levitated particles. In combination with balanced detection and feedback cooling, this system has provided picometer scale position sensitivity, zeptonewton force detection, and sub-millikelvin CM temperatures. In this article, we develop an analytical model of this detection system and compare its performance with experimental results allowing us to explain the presence of spurious frequencies in the spectra.
Atomic force microscope (AFM) users often calibrate the spring constants of cantilevers using functionality built into individual instruments. This is performed without reference to a global standard, which hinders robust comparison of force measurements reported by different laboratories. In this article, we describe a virtual instrument (an internet-based initiative) whereby users from all laboratories can instantly and quantitatively compare their calibration measurements to those of others - standardising AFM force measurements - and simultaneously enabling non-invasive calibration of AFM cantilevers of any geometry. This global calibration initiative requires no additional instrumentation or data processing on the part of the user. It utilises a single website where users upload currently available data. A proof-of-principle demonstration of this initiative is presented using measured data from five independent laboratories across three countries, which also allows for an assessment of current calibration.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
