Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userAnatomy of Type-X Spin-Orbit Torque Switching
71
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Using type-x spin-orbit torque (SOT) switching scheme, in which the easy axis (EA) of the ferromagnetic (FM) layer and the charge current flow direction are collinear, is possible to realize a lower-power-consumption, higher-density, and better-performance SOT magnetoresistive random access memory (SOT-MRAM) as compared to the conventional type-y design. Here, we systematically investigate type-x SOT switching properties by both macrospin and micromagnetic simulations. The out-of-plane external field and anisotropy field dependence of the switching current density ($J_{sw}$) is first examined in the ideal type-x configuration. Next, we study the FM layer canting angle ($phi_{EA}$) dependence of $J_{sw}$ through macrospin simulations and experiments, which show a transformation of switching dynamics from type-x to type-y with increasing $phi_{EA}$. By further integrating field-like torque (FLT) into the simulated system, we find that a positive FLT can assist type-x SOT switching while a negative one brings about complex dynamics. More crucially, with the existence of a sizable FLT, type-x switching mode results in a lower critical switching current than type-y at current pulse width less than ~ 10 ns, indicating the advantage of employing type-x design for ultrafast switching using materials systems with FLT. Our work provides a thorough examination of type-x SOT scheme with various device/materials parameters, which can be informative for designing next-generation SOT-MRAM.
rate research
Read More
Current-induced control of magnetization in ferromagnets using spin-orbit torque (SOT) has drawn attention as a new mechanism for fast and energy efficient magnetic memory devices. Energy-efficient spintronic devices require a spin-current source with a large SOT efficiency (${xi}$) and electrical conductivity (${sigma}$), and an efficient spin injection across a transparent interface. Herein, we use single crystals of the van der Waals (vdW) topological semimetal WTe$_2$ and vdW ferromagnet Fe$_3$GeTe$_2$ to satisfy the requirements in their all-vdW-heterostructure with an atomically sharp interface. The results exhibit values of ${xi}{approx}4.6$ and ${sigma}{approx}2.25{times}10^5 {Omega}^{-1} m^{-1}$ for WTe$_2$. Moreover, we obtain the significantly reduced switching current density of $3.90{times}10^6 A/cm^2$ at 150 K, which is an order of magnitude smaller than those of conventional heavy-metal/ ferromagnet thin films. These findings highlight that engineering vdW-type topological materials and magnets offers a promising route to energy-efficient magnetization control in SOT-based spintronics.
Spin-orbit torque enables electrical control of the magnetic state of ferromagnets or antiferromagnets. In this work we consider the spin-orbit torque in the 2-d Van der Waals antiferromagnetic bilayer CrI$_3$, in the $n$-doped regime. In the purely antiferromagnetic state, two individually inversion-symmetry broken layers of CrI$_3$ form inversion partners, like the well-studied CuMnAs and Mn$_2$Au. However, the exchange and anisotropy energies are similar in magnitude, unlike previously studied antiferromagnets, which leads to qualitatively different behaviors in this material. Using a combination of first-principles calculations of the spin-orbit torque and an analysis of the ensuing spin dynamics, we show that the deterministic electrical switching of the Neel vector is the result of dampinglike spin-orbit torque, which is staggered on the magnetic sublattices.
Reducing energy dissipation while increasing speed in computation and memory is a long-standing challenge for spintronics research. In the last 20 years, femtosecond lasers have emerged as a tool to control the magnetization in specific magnetic materials at the picosecond timescale. However, the use of ultrafast optics in integrated circuits and memories would require a major paradigm shift. An ultrafast electrical control of the magnetization is far preferable for integrated systems. Here we demonstrate reliable and deterministic control of the out-of-plane magnetization of a 1 nm-thick Co layer with single 6 ps-wide electrical pulses that induce spin-orbit torques on the magnetization. We can monitor the ultrafast magnetization dynamics due to the spin-orbit torques on sub-picosecond timescales, thus far accessible only by numerical simulations. Due to the short duration of our pulses, we enter a counter-intuitive regime of switching where heat dissipation assists the reversal. Moreover, we estimate a low energy cost to switch the magnetization, projecting to below 1fJ for a (20 nm)^3 cell. These experiments prove that spintronic phenomena can be exploited on picosecond time-scales for full magnetic control and should launch a new regime of ultrafast spin torque studies and applications.
Symmetry breaking is a characteristic to determine which branch of a bifurcation system follows upon crossing a critical point. Specifically, in spin-orbit torque (SOT) devices, a fundamental question arises: how to break the symmetry of the perpendicular magnetic moment by the in-plane spin polarization? Here, we show that the chiral symmetry breaking by the DMI can induce the deterministic SOT switching of the perpendicular magnetization. By introducing a gradient of saturation magnetization or magnetic anisotropy, non-collinear spin textures are formed by the gradient of effective SOT strength, and thus the chiral symmetry of the SOT-induced spin textures is broken by the DMI, resulting in the deterministic magnetization switching. We introduce a strategy to induce an out-of-plane (z) gradient of magnetic properties, as a practical solution for the wafer-scale manufacture of SOT devices.
While tremendous work has gone into spin-orbit torque and spin current generation, charge-to-spin conversion efficiency remains weak in silicon to date, generally stemming from the low spin-orbit coupling (low atomic number, Z) and lack of bulk lattice inversion symmetry breaking. Here we report the observation of spin-orbit torque in an amorphous, non-ferromagnetic Fe$_{x}$Si$_{1-x}$ / cobalt bilayer at room temperature, using spin torque ferromagnetic resonance and harmonic Hall measurements. Both techniques provide a minimum spin torque efficiency of about 3 %, comparable to prototypical heavy metals such as Pt or Ta. According to the conventional theory of the spin Hall effect, a spin current in an amorphous material is not expected to have any substantial contribution from the electronic bandstructure. This, combined with the fact that Fe$_{x}$Si$_{1-x}$ does not contain any high-Z element, paves a new avenue for understanding the underlying physics of spin-orbit interaction and opens up a new class of material systems - silicides - that is directly compatible with complementary metal-oxide-semiconductor (CMOS) processes for integrated spintronics applications.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
