Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userNanoscale axial position and orientation measurement of hexagonal boron nitride quantum emitters using a tunable nanophotonic environment
384
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Color centers in hexagonal boron nitride (hBN) have emerged as promising candidates for single-photon emitters (SPEs) due to their bright emission characteristics at room temperature. In contrast to mono- and few-layered hBN, color centers in multi-layered flakes show superior emission characteristics such as higher saturation counts and spectral stability. Here, we report a method for determining both the axial position and three-dimensional dipole orientation of SPEs in thick hBN flakes by tuning the photonic local density of states using vanadium dioxide (VO2), a phase change material. Emitters under study exhibit a strong surface-normal dipole orientation, providing some insight on the atomic structure of hBN SPEs, deeply embedded in thick crystals. We have optimized a hot pickup technique to reproducibly transfer flakes of hBN from VO2 onto SiO2/Si substrate and relocated the same emitters. Our approach serves as a practical method to systematically characterize SPEs in hBN prior to integration in quantum photonics systems.
rate research
Read More
Nanoscale optical thermometry is a promising non-contact route for measuring local temperature with both high sensitivity and spatial resolution. In this work, we present a deterministic optical thermometry technique based on quantum emitters in nanoscale hexagonal boron-nitride. We show that these nanothermometers exhibit better performance than that of homologous, all-optical nanothermometers both in sensitivity and range of working temperature. We demonstrate their effectiveness as nanothermometers by monitoring the local temperature at specific locations in a variety of custom-built micro-circuits. This work opens new avenues for nanoscale temperature measurements and heat flow studies in miniaturized, integrated devices.
Luminescent defect-centers in hexagonal boron nitride (hBN) have emerged as a promising 2D-source of single photon emitters (SPEs) due to their high brightness and robust operation at room temperature. The ability to create such emitters with well-defined optical properties is a cornerstone towards their integration into on-chip photonic architectures. Here, we report an effective approach to fabricate hBN single photon emitters (SPEs) with desired emission properties in two isolated spectral regions via the manipulation of boron diffusion through copper during atmospheric pressure chemical vapor deposition (APCVD)--a process we term gettering. Using the gettering technique we deterministically place the resulting zero-phonon line (ZPL) between the regions 550-600 nm or from 600-650 nm, paving the way for hBN SPEs with tailored emission properties across a broad spectral range. Our ability to control defect formation during hBN growth provides a simple and cost-effective means to improve the crystallinity of CVD hBN films, and lower defect density making it applicable to hBN growth for a wide range of applications. Our results are important to understand defect formation of quantum emitters in hBN and deploy them for scalable photonic technologies.
Development of scalable quantum photonic technologies requires on-chip integration of components such as photonic crystal cavities and waveguides with nonclassical light sources. Recently, hexagonal boron nitride (hBN) has emerged as a promising platform for nanophotonics, following reports of hyperbolic phonon-polaritons and optically stable, ultra-bright quantum emitters. However, exploitation of hBN in scalable, on-chip nanophotonic circuits, quantum information processing and cavity quantum electrodynamics (QED) experiments requires robust techniques for the fabrication of monolithic optical resonators. In this letter, we design and engineer high quality photonic crystal cavities from hBN. We employ two approaches based on a focused ion beam method and a minimally-invasive electron beam induced etching (EBIE) technique to fabricate suspended two dimensional (2D) and one dimensional (1D) cavities with quality (Q) factors in excess of 2,000. Subsequently, we show deterministic, iterative tuning of individual cavities by direct-write, single-step EBIE without significant degradation of the Q-factor. The demonstration of tunable, high Q cavities made from hBN is an unprecedented advance in nanophotonics based on van der Waals materials. Our results and hBN processing methods open up promising new avenues for solid-state systems with applications in integrated quantum photonics, polaritonics and cavity QED experiments.
Growing interest in devices based on layered van der Waals (vdW) materials is motivating the development of new nanofabrication methods. Hexagonal boron nitride (hBN) is one of the most promising materials for studies of quantum photonics and polaritonics. Here, we report in detail on a promising nanofabrication processes used to fabricate several hBN photonic devices using a hybrid electron beam induced etching (EBIE) and reactive ion etching (RIE) technique. We highlight the shortcomings and benefits of RIE and EBIE and demonstrate the utility of the hybrid approach for the fabrication of suspended and supported device structures with nanoscale features and highly vertical sidewalls. Functionality of the fabricated devices is proven by measurements of high quality cavity optical modes (Q~1500). Our nanofabrication approach constitutes an advance towards an integrated, monolithic quantum photonics platform based on hBN and other layered vdW materials.
Fluorescent nanoparticles are widely utilized in a large range of nanoscale imaging and sensing applications. While ultra-small nanoparticles (size <10 nm) are highly desirable, at this size range their photostability can be compromised due to effects such as intensity fluctuation and spectral diffusion caused by interaction with surface states. In this letter, we demonstrate a facile, bottom-up technique for the fabrication of sub-10-nm hBN nanoparticles hosting photostable bright emitters via a catalyst-free hydrothermal reaction between boric acid and melamine. We also implement a simple stabilization protocol that significantly reduces intensity fluctuation by ~85% and narrows the emission linewidth by ~14% by employing a common sol-gel silica coating process. Our study advances a promising strategy for the scalable, bottom-up synthesis of high-quality quantum emitters in hBN nanoparticles.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
