Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userStudies on tetrafluoropropene-based gas mixtures with low environmental impact for Resistive Plate Chambers
295
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Gaseous detectors are widely used in high-energy physics experiments, and in particular at the CERN Large Hadron Collider (LHC), to provide tracking and triggering over large volumes. It has been recently estimated that Resistive Plate Chambers (RPC), used for muon detection, have the highest contribution on the overall greenhouse gas (GHG) emissions at the LHC experiments. Gas mixtures for RPCs are mainly made of C$_{2}$H$_{2}$F$_{4}$, which is a greenhouse gas with a high environmental impact in the atmosphere. C$_{2}$H$_{2}$F$_{4}$ is already phasing out of production, due to recent European Union (EU) regulations, and its cost is expected to increase in the near future. Therefore, finding alternative gas mixtures made of gas components with a low Global Warming Potential (GWP) has become extremely important for limiting the GHG emissions as well as for economic reasons. The novel hydrofluoroolefins are likely appropriate candidates to replace C$_{2}$H$_{2}$F$_{4}$ due to their similar chemical structures. This study is focused on the characterization of innovative gas mixtures with tetrafluoropropene HFO1234ze(E) (C$_{3}$H$_{2}$F$_{4}$) that is one of the most eco-friendly hydrofluoroolefins, thanks to its very low GWP. HFO1234ze(E)-based gas mixtures with the addition of Ar, N$_{2}$, O$_{2}$ and CO$_{2}$ are extensively discussed in this paper as well as the role of i-C$_{4}$H$_{10}$ and SF$_{6}$ in such mixtures.
rate research
Read More
The muon identification system of the ALICE experiment at the CERN LHC is based on Resistive Plate Chamber (RPC) detectors. These RPCs are operated in the so-called maxi-avalanche mode with a gas mixture made of tetrafluoroethane (C$_{2}$H$_{2}$F$_{4}$), sulfur hexafluoride (SF$_{6}$) and isobutane (i-C$_{4}$H$_{10}$). All of these components are greenhouse gases: in particular, the first two gases are already phasing out of production, due to recent European Union regulations, and their cost is progressively increasing. Therefore, finding a new eco-friendly gas mixture has become extremely important in order to reduce the impact of the RPC operation on the environment, and for economic reasons. Due to the similar chemical structure, hydrofluoroolefins appear appropriate candidates to replace C$_{2}$H$_{2}$F$_{4}$ thanks to their very low GWPs, especially tetrafluoropropene (C$_{3}$H$_{2}$F$_{4}$) with the trade name HFO1234ze. In order to identify an eco-friendly gas mixture fulfilling the requirements for operation in the ALICE environment in the coming years, a dedicated experimental set-up has been built to carry out R&D studies on promising gas mixtures. Measurements have been performed with a small-size RPC equipped with the front-end electronics, providing signal amplification, developed for ALICE operation at high luminosity after the LHC Long Shutdown 2. HFO1234ze-based mixtures with the addition of CO$_{2}$ are discussed in this paper as well as the role of i-C$_{4}$H$_{10}$ and SF$_{6}$ as quenchers in such mixtures.
Resistive Plate Chambers (RPC) have shown stable operation at the Large Hadron Collider and satisfactory efficiency for the entire Run 1 (2010-2013) and Run 2 (2015-2018) with C$_{2}$H$_{2}$F$_{4}$-based gas mixtures and the addition of SF$_{6}$ and i-C$_{4}$H$_{10}$. Since its global warming potential (GWP) is high, C$_{2}$H$_{2}$F$_{4}$ is phasing out of production due to recent European Union regulations and as a result its cost is progressively increasing. Therefore, finding a new RPC gas mixture with a low GWP has become extremely important. This contribution describes the simulation of the RPC efficiency with tetrafluoropropene C$_{3}$H$_{2}$F$_{4}$ (HFO1234ze), a hydrofluoroolefin with very low GWP. Simulation results are systematically compared with measurements of RPC efficiency in C$_{3}$H$_{2}$F$_{4}$-based gas mixtures with the addition of different combinations of Ar, He, CO$_{2}$, O$_{2}$ and i-C$_{4}$H$_{10}$ in various concentrations. This simulation allows the study of the interplay between C$_{3}$H$_{2}$F$_{4}$ and the other gas components in the mixture as well as may allow the identification of the most promising environment-friendly gas mixtures with C$_{3}$H$_{2}$F$_{4}$ for RPCs.
We report on studies of fast triggering and high-precision tracking using Resistive Plate Chambers (RPCs). Two beam tests were carried out with the 180 GeV muon beam at CERN using RPCs with gas gaps of 1.00 or 1.15 mm and equipped with readout strips with 1.27 mm pitch. This is the first beam test of RPCs with fine-pitch readout strips that explores simultaneously precision tracking and triggering capabilities. RPC signals were acquired with precision timing and charge integrating readout electronics at both ends of the strips. The time resolution was measured to be better than 600 ps and the average spatial resolution was found to be 220 um using charge information and 287 um using timing information. The dual-ended readout allows the determination of the average and the difference of the signal arrival times. The average time was found to be independent of the incident particle position along the strip and is useful for triggering purposes. The time difference yielded a determination of the hit position with a precision of 7.5 mm along the strip. These results demonstrate the feasibility using RPCs for fast and high-resolution triggering and tracking.
The DHCAL, the Digital Hadron Calorimeter, is a prototype calorimeter based on Resistive Plate Chambers (RPCs). The design emphasizes the imaging capabilities of the detector in an effort to optimize the calorimeter for the application of Particle Flow Algorithms (PFAs) to the reconstruction of hadronic jet energies in a colliding beam environment. The readout of the chambers is segmented into 1 x 1 cm2 pads, each read out with a 1-bit (single threshold) resolution. The prototype with approximately 500,000 readout channels underwent extensive testing in both the Fermilab and CERN test beams. This talk presents preliminary findings from the analysis of data collected at the test beams.
The Resistive Plate Chamber (RPC) muon subsystem contributes significantly to the formation of the trigger decision and reconstruction of the muon trajectory parameters. Simulation of the RPC response is a crucial part of the entire CMS Monte Carlo software and directly influences the final physical results. An algorithm based on the parametrization of RPC efficiency, noise, cluster size and timing for every strip has been developed. Experimental data obtained from cosmic and proton-proton collisions at $sqrt{s}=7$ TeV have been used for determination of the parameters. A dedicated validation procedure has been developed. A good agreement between the simulated and experimental data has been achieved.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
