Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userEnergy-Based Weak Measurement
94
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
When a well-localized photon is incident on a spatially superposed absorber but is not absorbed, the photon can still deliver energy to the absorber. It is shown that when the transferred energy is small relative to the energy uncertainty of the photon, this constitutes an unusual type of weak measurement of the absorbers energy, where the energy distribution of the unabsorbed photon acts as the measurement device, and the strongly disturbed state of the absorber becomes the effective pre-selection. Treating the final state of the absorber as the post-selection, it is shown that the absorbers energy increase is the weak value of its translational Hamiltonian, and the energy distribution of the photon shifts by the opposite amount. The basic case of non-scattering is examined, followed by the case of interaction-free energy transfer. Details and interpretations of the results are discussed.
rate research
Read More
We analyze the operation of a switching-based detector that probes a qubits observable that does not commute with the qubits Hamiltonian, leading to a nontrivial interplay between the measurement and free-qubit dynamics. In order to obtain analytic results and develop intuitive understanding of the different possible regimes of operation, we use a theoretical model where the detector is a quantum two-level system that is constantly monitored by a macroscopic system. We analyze how to interpret the outcome of the measurement and how the state of the qubit evolves while it is being measured. We find that the answers to the above questions depend on the relation between the different parameters in the problem. In addition to the traditional strong-measurement regime, we identify a number of regimes associated with weak qubit-detector coupling. An incoherent detector whose switching time is measurable with high accuracy can provide high-fidelity information, but the measurement basis is determined only upon switching of the detector. An incoherent detector whose switching time can be known only with low accuracy provides a measurement in the qubits energy eigenbasis with reduced measurement fidelity. A coherent detector measures the qubit in its energy eigenbasis and, under certain conditions, can provide high-fidelity information.
As the minituarization of electronic devices, which are sensitive to temperature, grows apace, sensing of temperature with ever smaller probes is more important than ever. Genuinely quantum mechanical schemes of thermometry are thus expected to be crucial to future technological progress. We propose a new method to measure the temperature of a bath using the weak measurement scheme with a finite dimensional probe. The precision offered by the present scheme not only shows similar qualitative features as the usual Quantum Fisher Information based thermometric protocols, but also allows for flexibility over setting the optimal thermometric window through judicious choice of post selection measurements.
We present a general framework of examining the validity of weak measurement -- the standard procedure to acquire Aharonovs weak value -- which has been used intensively in recent years for precision measurement, taking advantage of the amplification mechanism available for the weak value. Our framework allows one to deal systematically with various causes of uncertainties intrinsic to the actual measurement process as well as those found in the theoretical analysis employed to describe the system. Using our framework, we examine in detail the two seminal experiments, Hostens detection measurement of the spin Hall effect of light and Dixons ultra sensitive beam deflection measurement. Our analysis shows that their results are well within the range of amplification (actually in the vicinity of the optimal point) where the weak measurements are valid. This suggests that our framework is both practical and sound, and may be useful to determine beforehand the possible extent of amplification in the future weak measurement experiments.
Standard weak measurement (SWM) has been proved to be a useful ingredient for measuring small longitudinal phase shifts. [Phys. Rev. Lett. 111, 033604 (2013)]. In this letter, we show that with specfic pre-coupling and postselection, destructive interference can be observed for the two conjugated variables, i.e. time and frequency, of the meter state. Using a broad band source, this conjugated destructive interference (CDI) can be observed in a regime approximately 1 attosecond, while the related spectral shift reaches hundreds of THz. This extreme sensitivity can be used to detect tiny longitudinal phase perturbation. Combined with a frequency-domain analysis, conjugated destructive interference weak measurement (CDIWM) is proved to outperform SWM by two orders of magnitude.
We address the peculiarities of the quantum measurement process in the course of a continuous weak linear measurement (CWLM). As a tool, we implement an efficient numerical simulation scheme that allows us to generate single quantum trajectories of the measured system state as well as the recorded detector signal, and study statistics of these trajectories with and without post-selection. In this scheme, a linear detector is modelled with a qubit that is weakly coupled to the quantum system measured and is subject to projective measurement and re-initialization after a time interval at each simulation step. We explain the conditions under which the scheme provides an accurate description of CWLM. We restrict ourselves to a qubit non-demolition measurement. The qubit is initially in an equal-weight superposition of two quantum states. In the course of time, the detector signal is accumulated and the superposition is destroyed. The times required to resolve the quantum states and to destroy the superposition are of the same order. We prove numerically a rather counter intuitive fact: the average detector output conditioned on the final state does not depend on time. It looks like from the very beginning, the qubit knows in which state it is. We study statistics of decision times where the decision time is defined as time required for the density matrix along a certain trajectory to reach a threshold where it is close to one of the resulting states. This statistics is useful to estimate how fast a decisive CWLM can be. Basing on this, we devise and study a simple feedback scheme that attempts to keep the qubit in the equal-weight superposition. The detector readings are used to decide in which state the qubit is and which correction rotation to apply to bring it back to the superposition. We show how to optimize the feedback parameters and move towards more efficient feedback schemes.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
