Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userFaster Lead-Acid Battery Simulations from Porous-Electrode Theory: II. Asymptotic Analysis
73
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Electrochemical and equivalent-circuit modelling are the two most popular approaches to battery simulation, but the former is computationally expensive and the latter provides limited physical insight. A theoretical middle ground would be useful to support battery management, on-line diagnostics, and cell design. We analyse a thermodynamically consistent, isothermal porous-electrode model of a discharging lead-acid battery. Asymptotic analysis of this full model produces three reduced-order models, which relate the electrical behaviour to microscopic material properties, but simulate discharge at speeds approaching an equivalent circuit. A lumped-parameter model, which neglects spatial property variations, proves accurate for C-rates below 0.1C, while a spatially resolved higher-order solution retains accuracy up to 5C. The problem of parameter estimation is addressed by fitting experimental data with the reduced-order models.
rate research
Read More
An isothermal porous-electrode model of a discharging lead-acid battery is presented, which includes an extension of concentrated-solution theory that accounts for excluded-volume effects, local pressure variation, and a detailed microscopic water balance. The approach accounts for three typically neglected physical phenomena: convection, pressure diffusion, and variation of liquid volume with state of charge. Rescaling of the governing equations uncovers a set of fundamental dimensionless parameters that control the batterys response. Total volume change during discharge and nonuniform pressure prove to be higher-order effects in cells where variations occur in just one spatial dimension. A numerical solution is developed and exploited to predict transient cell voltages and internal concentration profiles in response to a range of C-rates. The dependence of discharge capacity on C-rate deviates substantially from Peukerts simple power law: charge capacity is concentration-limited at low C-rates, and voltage-limited at high C-rates. The model is fit to experimental data, showing good agreement.
We present a porous electrode model for lithium-ion batteries using Butler--Volmer reaction kinetics. We model lithium concentration in both the solid and fluid phase along with solid and liquid electric potential. Through asymptotic reduction, we show that the electric potentials are spatially homogeneous which decouples the problem into a series of time-dependent problems. These problems can be solved on three distinguished time scales, an early time scale where capacitance effects in the electrode dominate, a mid-range time scale where a spatial concentration gradient forms in the electrolyte, and a long-time scale where each of the electrodes saturate and deplete with lithium respectively. The solid-phase concentration profiles are linear functions of time and the electrolyte potential is everywhere zero, which allows the model to be reduced to a system of two uncoupled ordinary differential equations. Analytic and numerical results are compared with full numerical simulations and experimental discharge curves demonstrating excellent agreement.
The rapid charging and/or discharging of electrochemical cells can lead to localized depletion of electrolyte concentration. This depletion can significantly impact the systems time dependent resistance. For systems with porous electrodes, electrolyte depletion can limit the rate of charging and increase energy dissipation. Here we propose a theory to control and avoid electrolyte depletion by tailoring the value and spatial distribution of resistance in a porous electrode. We explore the somewhat counterintuitive idea that increasing local spatial resistances of the solid electrode itself leads to improved charging rate and minimal change in energy loss. We analytically derive a simple expression for an electrode resistance profile that leads to highly uniform electrolyte depletion. We use numerical simulations to explore this theory and simulate spatiotemporal dynamics of electrolyte concentration in the case of a supercapacitor with various tailored electrode resistance profiles which avoid localized depletion. This increases charging rate up to around 2-fold with minimal effect on overall dissipated energy in the system.
In order for the widely discussed benefits of flow batteries for electrochemical energy storage to be applied at large scale, the cost of the electrochemical stack must come down substantially. One promising avenue for reducing stack cost is to increase the system power density while maintaining efficiency, enabling smaller stacks. Here we report on a membrane-less, hydrogen bromine laminar flow battery as a potential high power density solution. The membrane-less design enables power densities of 0.795 W cm$^{-2}$ at room temperature and atmospheric pressure, with a round-trip voltage efficiency of 92% at 25% of peak power. Theoretical solutions are also presented to guide the design of future laminar flow batteries. The high power density achieved by the hydrogen bromine laminar flow battery, along with the potential for rechargeable operation, will translate into smaller, inexpensive systems that could revolutionize the fields of large-scale energy storage and portable power systems.
Structures and minimum molecular electrostatic potential (MEP) distributions in anacardic acid and some of its derivatives have been studied by full geometry optimization at the M06-2X/6-31G(d,p), WB97XD/6-31G(d,p) and B3LYP/6-31G(d,p) levels of density functional theory (DFT) in gas phase as well as in DMSO and aqueous solutions. Solvent effect was treated employing the integral equation formalism of the polarizable continuum model. Effects of modifications of the C1-side chain on the minimum MEP values in various regions were studied. Minimum MEP values near the oxygen atoms of the C2-OH group, oxygen or sulfur atoms of the C1-attached urea or thiourea groups and above or below the ring plane considered to be involved in interaction with the receptor were used to perform multiple linear regression. Experimentally observed anti-bacterial activities of these molecules against S. aureus are thus shown to be related to minimum MEP values in the above mentioned regions. Among the three DFT functionals used in the study, the M06-2X functional is found to yield most reliable results. Anti-bacterial activities have been predicted for certain molecules of the class which need to be verified experimentally.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
