Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userTheory, design, and experimental verification of a reflectionless bianisotropic Huygens metasurface for wide-angle refraction
96
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Huygens metasurfaces are electrically thin devices which allow arbitrary field transformations. Beam refraction is among the first demonstrations of realized metasurfaces. As previously shown for extreme-angle refraction, control over only the electric impedance and magnetic admittance of the Huygens metasurface proved insufficient to produce the desired reflectionless field transformation. To maintain zero reflections for wide refraction angles, magnetoelectric coupling between the electric and magnetic response of the metasurface, leading to bianisotropy, can be introduced. In this paper, we report the theory, design, and experimental characterization of a reflectionless bianisotropic metasurface for extreme-angle refraction of a normally incident plane wave towards 71.8$^circ$ at 20 GHz. The theory and design of three-layer asymmetric bianisotropic unit cells are discussed. The realized printed circuit board structure was tested via full-wave simulations as well as experimental characterization. To experimentally verify the prototype, two setups were used. A quasi-optical experiment was conducted to assess the specular reflections of the metasurface, while a far-field antenna measurement characterized its refraction nature. The measurements verify that the fabricated metasurface has negligible reflections and the majority of the scattered power is refracted to the desired Floquet mode. This provides an experimental demonstration of a reflectionless wide-angle refracting metasurface using a bianisotropic Huygens metasurface at microwave frequencies.
rate research
Read More
Metasurfaces are an enabling technology for complex wave manipulation functions, including in the terahertz frequency range, where they are expected to advance security, imaging, sensing, and communications technology. For operation in transmission, Huygens metasurfaces are commonly used, since their good impedance match to the surrounding media minimizes reflections and maximizes transmission. Recent theoretical work has shown that Huygens metasurfaces are non-optimal, particularly for large angles of refraction, and that to eliminate reflections and spurious diffracted beams it is necessary to use a bianisotropic metasurface. However, it remains to be demonstrated how significant the efficiency improvement is when using bianisotropic metasurfaces, considering all the non-ideal features that arise when implementing the metasurface design with real meta-atoms. Here we compare concrete terahertz metasurface designs based on the Huygens and Omega-type bianisotropic approaches, demonstrating anomalous refraction angles for 55 degrees, and 70 degrees. We show that for the lower angle of 55 degrees, there is no significant improvement when using the bianisotropic design, whereas for refraction at 70 degrees the bianisotropic design shows much higher efficiency and fidelity of refraction into the designed direction. We also demonstrate the strong perturbations caused by near-field interaction, both between and within cells, which we compensate using numerical optimization.
In this paper, a novel concept of a leaky-wave antenna is proposed, based on the use of Huygens metasurfaces. It consists of a parallel-plate waveguide in which the top plate is replaced by a bianisotropic metasurface of the Omega type. It is shown that there is an exact solution to transform the guided mode into a leaky-mode with arbitrary control of the constant leakage factor and the pointing direction. Although the solution turns out to be periodic, only one Floquet mode is excited and radiates, even for electrically long periods. Thanks to the intrinsic spurious Floquet mode suppression, broadside radiation can be achieved without any degradation. Simulations with idealized reactance sheets verify the concept. Moreover, physical structures compatible with PCB fabrication have been proposed and designed, considering aspects such as the effect of losses. Finally, experimental results of two prototypes are presented and discussed.
Although a rigorous theoretical ground on metasurfaces has been established in the recent years on the basis of the equivalence principle, the majority of metasurfaces for converting a propagating wave into a surface wave are developed in accordance with the so-called generalized Snells law being a simple heuristic rule for performing wave transformations. Recently, for the first time, Tcvetkova et al. [Phys. Rev. B 97, 115447 (2018)] have rigorously studied this problem by means of a reflecting anisotropic metasurface, which is, unfortunately, difficult to realize, and no experimental results are available. In this paper, we propose an alternative practical design of a metasurface-based converter by separating the incident plane wave and the surface wave in different half-spaces. It allows one to preserve the polarization of the incident wave and substitute the anisotropic metasurface by an omega-bianisotropic one. The problem is approached from two sides: By directly solving the corresponding boundary problem and by considering the ``time-reversed scenario when a surface wave is converted into a nonuniform plane wave. We develop a practical three-layer metasurface based on a conventional printed circuit board technology to mimic the omega-bianisotropic response. The metasurface incorporates metallic walls to avoid coupling between adjacent unit cells and accelerate the design procedure. The design is validated with full-wave three-dimensional numerical simulations and demonstrates high conversion efficiency.
Metasurface with gradient phase response offers new alternative for steering the propagation of waves. Conventional Snells law has been revised by taking the contribution of local phase gradient into account. However, the requirement of momentum matching along the metasurface sets its nontrivial beam manipulation functionality within a limited-angle incidence. In this work, we theoretically and experimentally demonstrate that the acoustic gradient metasurface supports the negative reflection for all-angle incidence. The mode expansion theory is developed to help understand how the gradient metasurface tailors the incident beams, and the all-angle negative reflection occurs when the first negative order Floquet-Bloch mode dominates inside the metasurface slab. The coiling-up space structures are utilized to build desired acoustic gradient metasurface, and the all-angle negative reflections have been perfectly verified by experimental measurements. Our work offers the Floquet-Bloch modes perspective for qualitatively understanding the reflection behaviors of the acoustic gradient metasurface, and the all-angle negative reflection characteristic possessed by acoustic gradient metasurface could enable a new degree of the acoustic wave manipulating and be applied in the functional diffractive acoustic elements, such as the all-angle acoustic back reflector.
Metasurfaces provide the disruptive technology enabling miniaturization of complex cascades of optical elements on a plane. We leverage the benefits of such a surface to develop a planar integrated photonic beam collimator for on-chip optofluidic sensing applications. While most of the current work focuses on miniaturizing the optical detection hardware, little attention is given to develop on-chip hardware for optical excitation. In this manuscript, we propose a flat metasurface for beam collimation in optofluidic applications. We implement an inverse design approach to optimize the metasurface using gradient descent method and experimentally compare its characteristics with conventional binary grating-based photonic beam diffractors. The proposed metasurface can enhance the illumination efficiency almost two times in on-chip applications such as fluorescence imaging, Raman and IR spectroscopy and can enable multiplexing of light sources for high throughput biosensing.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
